ADM3485ARZ-REEL7
Product Specifications
ADM3485ARZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADM3485ARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADM3485ARZ-REEL7: a half duplex 3.3 V RS-485 transceiver at 10 Mbps
What this order code is
ADM3485ARZ-REEL7 is a half duplex differential line transceiver for RS-485 and RS-422 buses, running from a single 3.3 V supply at up to 10 Mbps, in an 8-lead SOIC. It has separate driver and receiver enable pins, which is what a two wire bus requires: the driver has to be tri-stated while the same pair is receiving, and the software has to turn it around.
The receiver input impedance is 12 kilohms, allowing 32 transceivers on one bus, and the common mode range is minus 7 V to plus 12 V. Fail-safe behaviour holds the receiver output high when the inputs are open, the driver outputs go high impedance when the part is disabled or unpowered, and thermal shutdown plus short circuit protection guard against bus contention. Skew is 8 ns, the logic side is interoperable with 5 V logic, and shutdown current is 2 nA. This is the non-E member of the family, so the plus or minus 15 kV bus pin rating of the E parts does not apply here.
Parameters as published
| Item | Value |
|---|---|
| Supply | 3.3 V |
| Duplex | half duplex, driver and receiver enable pins |
| Data rate | 10 Mbps |
| Bus standard | EIA RS-485 and RS-422 over the full common mode range |
| Nodes on the bus | 32, receiver input 12 kilohms |
| Common mode range | minus 7 V to plus 12 V |
| Skew | 8 ns |
| Shutdown current | 2 nA |
| Logic compatibility | interoperable with 5 V logic |
| Fail-safe | receiver output high on open inputs |
| Protection | thermal shutdown, short circuit |
| Package | 8-lead SOIC |
Numbers that decide the application
At 10 Mbps a bit is 100 ns and 8 ns of skew is 8 percent of it, which is the budget that has to absorb cable skew and receiver threshold variation as well. A 10 Mbps link therefore assumes a terminated pair of modest length, and the 120 ohm terminations at each end are not optional. Thirty two nodes of 12 kilohms in parallel is 375 ohms of load on the driver, which is why the standard stops at 32 unless a lower impedance receiver is used.
Half duplex costs nothing in copper and everything in software. The driver enable and receiver enable have to be sequenced so that the driver is off before the receiver is enabled, and a bus that is turned around too early shows up as corrupted first bytes rather than as a clean failure. The 10 Mbps rate makes that window 100 ns wide, which is why half duplex links at this rate are usually driven by hardware rather than by a general purpose port pin.
The absence of the E grade is a procurement fact with field consequences. The bus pins here carry the standard ESD rating and not the plus or minus 15 kV of the E parts, so a board that expects a field port to survive repeated hot plugging should either specify the E code or add external protection. Both are legitimate, and the difference is one letter in the order code.
Selection and cross reference notes
The family splits on duplex, data rate and ESD grade, and the packages are similar enough that a wrong member usually fits. The fields to match in order are half or full duplex, the enable pins, the data rate and the ESD grade. A full duplex part in a half duplex socket will drive the pair continuously, which is a bus fault rather than a performance shortfall.
The 3.3 V supply with 5 V logic interoperability means the part can sit on a mixed logic board without a level translator on the logic side. The bus side is a differential pair and is independent of the logic supply, which is the property that makes RS-485 useful over long cable runs.
Where it fits
Low power RS-485 links in telecom, industrial process control, HVAC and building automation. Half duplex is the normal choice where the bus is a single pair and the protocol is request and response, and 10 Mbps is used on short backplanes where the cable is controlled. Buyers checking a replacement can start at the second source page, and teams comparing interface parts usually work from the power management cross reference hub.
Buying notes
ARZ is the 8-lead SOIC and REEL7 is the reel; the E grade carries an E in the family number and a different ESD rating. Because the E and non-E parts share a datasheet, a quotation should state which one is on offer. The enable pins are the other field worth confirming on a substitute, because a part without them cannot work on a two wire bus.
Sourcing notes and next step
The questions for an RS-485 transceiver are the duplex, the data rate, the ESD grade and the enable pins. We quote the exact code and confirm the grade before shipping. Send the codes and quantities, together with the bus length and node count, through the BOM shortage recovery page and we will answer with availability and the fields a substitute would change.
Request Quote — In Stock, 100% New & Original, Full Warranty