Contact Us

ADM3202ARNZ

Brand: Analog Devices
Analog Devices ADM3202ARNZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADM3202ARNZ — Analog & Mixed-Signal ICs | Superb Automation

ADM3202ARNZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADM3202ARNZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADM3202ARNZ: 3.3 V RS-232 interface with 0.1 uF charge pump capacitors

The ADM3202ARNZ is a 3.3 V RS-232 transmitter and receiver pair in a 16-lead narrow SOIC that generates its own positive and negative RS-232 levels from four 0.1 uF capacitors. It is quoted as the 3.3 V replacement for the 5 V parts that a serial port was originally built around.

Published values

ParameterValue
InterfaceEIA-232E, specified at 3.3 V
Data rate460 kbps
Charge pump capacitors0.1 uF
ESD on RS-232 pins8 kV contact, 15 kV air gap, ADM3202 only
Supply current1.3 mA typ, 3 mA max unloaded
Load current8 mA typ, 12 mA max into 3 kohm
Compatibilityupgrade path for MAX3222, MAX3232 and LTC1385
Package and range16-lead narrow SOIC, -40 C to +85 C

Where 3.3 V changes the RS-232 levels

RS-232 requires at least plus and minus 5 V at the transmitter output into a 3 kohm load, and the part produces them by doubling and inverting the 3.3 V rail with the charge pump. The 0.1 uF capacitors are what make that possible in a small package: they store and transfer the charge at a switching frequency high enough that the output droops by a defined amount between cycles.

The limit is load current. At 3.3 V the available headroom is smaller than at 5 V, so the same 3 kohm load draws a larger fraction of the pump capacity. The supply current figure of 12 mA maximum into 3 kohm is the loaded number, and 3 mA maximum is the unloaded one; a budget built on the unloaded number will be short.

460 kbps against a 2.17 us bit

At 460 kbps a bit is 2.17 us. That is slow by modern standards and it is what the RS-232 specification allows when the cable capacitance is in the specification. A 1 nF cable at 460 kbps needs the transmitter slew rate to charge the line within the bit, and the data sheet specifies the part into 50 pF to 1000 pF, which covers a screened cable of a few metres.

An opto-isolated or long cable installation is where the rate is actually limited: the cable capacitance dominates, and the transceiver that can drive 1000 pF at 460 kbps is doing more work than the data rate suggests.

ESD on the connector side

The 8 kV contact and 15 kV air gap ratings apply to the RS-232 pins on the ADM3202 only, which is the member of the trio that carries the protection. A board that fits the pin compatible part without the protection and expects the same surge performance is relying on a rating the order code does not carry.

The logic side is ordinary 3.3 V CMOS and has no such rating, so the protection boundary is the transceiver, and the connector shield has to be bonded on the outside of that boundary.

Replacement checks

The pin compatible parts in this group differ in whether they have the ESD protection and whether they have a shutdown pin. The footprint is shared, which is exactly why the suffix has to be read.

The pages below hold the cross reference, the shortage route and the acceptance sequence.

Two pages worth reading before a purchase order goes out are the pin to pin cross reference and the ADI second source page; the first lists what else fits the socket, the second is the test sequence for a drop in, and BOM shortage recovery covers the case where the shortage is already on the line.

Two questions buyers ask

Can the ADM3202ARNZ replace a MAX3232? The vendor lists this part as an upgrade path for the MAX3222, MAX3232 and LTC1385 with the same 0.1 uF capacitor arrangement, and the differences are in the protection and shutdown options rather than in the interface.

Does it need a negative supply rail? No. The charge pump generates the negative transmitter level from the 3.3 V rail, which is what the four 0.1 uF capacitors are for.