Contact Us

ADR3425ARJZ-R7

Brand: Analog Devices
Analog Devices ADR3425ARJZ-R7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADR3425ARJZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

ADR3425ARJZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADR3425ARJZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADR3425ARJZ-R7: 5.8 mV of error on a 2.5 V reference before the converter is counted

The ADR3425ARJZ-R7 is a 2.5 V series reference in a 6-lead SOT-23 from Analog Devices, part of a family that spans 1.2 V to 5.0 V in the same package. Initial accuracy is plus or minus 0.1 percent, the maximum temperature coefficient is 8 ppm per degree C over the full -40 C to +125 C range, and the output sources 10 mA and sinks 3 mA. Quiescent current is 100 uA maximum, the dropout voltage is 250 mV at 2 mA, and the output noise is below 10 uV peak to peak from 0.1 Hz to 10 Hz. The family is trimmed at final assembly, and the data sheet calls out low hysteresis and low long term drift as the reasons the initial accuracy survives a reflow cycle and a few years in the field. It is on the analog and mixed-signal IC line card.

Adding the initial error to the drift gives the number a converter actually sees

Eight ppm per degree C across 165 degrees is 1320 ppm, or 3.30 mV on a 2.5 V output. The initial error of 0.1 percent is another 2.5 mV. The two add to 5.80 mV, which is 0.232 percent of the output, and against the 38.15 uV code of a 16-bit converter that is 152 codes. On a 12-bit converter the same error is 10 codes, so the part is comfortable there and marginal at 16 bits. The distinction matters when a customer asks whether a 0.1 percent reference suits a 16-bit measurement: the initial error alone is 66 codes, and no amount of calibration at one temperature removes the drift term.

ParameterVendor figureDerived figure
Output2.5 V, plus or minus 0.1 percent2.5 mV initial
Temperature coefficient8 ppm per degree C maximum3.30 mV over 165 degrees
Worst case totalinitial plus drift5.80 mV, 0.232 percent
In 16-bit codes38.15 uV per code152 codes
In 12-bit codes610 uV per code10 codes
Noise, 0.1 Hz to 10 Hzbelow 10 uV peak to peak1.67 uV rms, 0.044 of a 16-bit code
Quiescent current100 uA maximum0.25 mW at 2.5 V, 0.50 mW at 5 V
Dropout at 2 mA250 mVa 2.75 V rail is the floor for a 2.5 V output
Output currentplus 10 mA, minus 3 mAasymmetric, the sink side is the limit

The asymmetric output current decides what the reference can drive

Ten milliamps of source current and three milliamps of sink look generous until the load is a converter reference input that kicks charge back on every conversion. A successive approximation converter draws a transient at the start of each bit trial, and the reference has to absorb it without moving. Three milliamps of sink also rules out a bipolar output stage built around the reference, where the negative half of the swing has to be sunk. In practice the reference feeds a buffer and the buffer feeds the converter, and the 100 uA quiescent current is what makes that acceptable in a loop powered instrument.

Selection notes

  • The 6-lead SOT-23 keeps the reference next to the converter, and at 100 uA the trace resistance between them is not a thermal problem.
  • The family covers 1.2 V through 5.0 V in the same package, so a 3.0 V or 4.096 V span is an order code change rather than a board change.
  • A 250 mV dropout at 2 mA means a 3.0 V rail has 500 mV of headroom, which is enough for a lithium cell or a 3.3 V bus at minus 5 percent.
  • Where the drift term has to shrink, the ADR4525 family offers 2 ppm per degree C in the same function and a different package.

Questions buyers ask

Is 0.1 percent initial accuracy enough for a 16-bit measurement? Not on its own. The initial error is 66 codes and the drift adds 86 more, so a 16-bit measurement needs either a tighter grade or a calibration that is repeated over temperature.

Can it be powered from the same 3.3 V rail as the converter? Yes at 2 mA, because the dropout is 250 mV and the rail would have to fall below 2.75 V before the output moved.

References and the converters they feed are paired on ADC DAC cross reference, and the drop in checks for a board revision are on pin to pin cross reference.

Request Quote — In Stock, 100% New & Original, Full Warranty