Contact Us

ADG211AKNZ

Brand: Analog Devices
Analog Devices ADG211AKNZ is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG211AKNZ — Analog & Mixed-Signal ICs | Superb Automation

ADG211AKNZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG211AKNZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADG211AKNZ: a 115 ohm quad switch that handles plus and minus 15 V, with an end of life notice attached

The ADG211AKNZ is an Analog Devices quad single pole single throw analog switch built on an enhanced LC2MOS process, in a 16-pin DIP. It passes a plus and minus 15 V analog signal from a supply rated to 44 V, has a maximum on resistance of 115 ohm, a typical leakage of 0.5 nA, and TTL and CMOS compatible control inputs. The four switches are independently selectable and exhibit break before make action when driven together, which is what allows several outputs to be tied into a multiplexer without a momentary short. It can also run from a single 15 V supply when the signal is unipolar. The digital control logic is inverted between the ADG211A and the ADG212A, which is the only difference between the two parts. Analog Devices marks the part as not recommended for new builds. It is listed on the analog and mixed-signal IC line card.

115 ohm in series with a 1 k load is 11.5 percent of gain error

An analog switch is a resistor when it is on, and 115 ohm is the maximum over temperature rather than the typical value at 25 C. In series with a 1 k load that is 11.5 percent of the signal, which is a gain error unless the following stage is a high impedance buffer. Into a 10 k load it is 1.15 percent, and into 1 Megohm it is 0.0115 percent and irrelevant. That is the whole selection argument for a switch of this generation: it belongs in front of a high impedance amplifier, not inside a resistive divider, and any circuit that uses it as part of a matched attenuator has to account for the resistance and its drift.

ParameterVendor figureDerived figure
Configurationfour independent SPST switchesa 4 to 1 multiplexer with outputs tied
Signal rangeplus and minus 15 Va 30 V peak to peak swing through the switch
Supply rating44 V maximum2.93 times the signal range, room for a transient
On resistance115 ohm maximum11.5 percent into 1 k, 1.15 percent into 10 k
Leakage0.5 nA typical500 uV into 1 Megohm, 5 mV into 10 Megohm
Switching actionbreak before makeno short between channels when the code changes
Control levelsTTL and CMOS compatibledriven directly by 3.3 V or 5 V logic
Single supply use0 V to 15 V unipolarone rail when the signal never goes negative
Package16-pin DIPthrough hole, and the reason the part survives in installed equipment
Statusnot recommended for new buildsstill in production, replacement demand only

Half a nanoamp of leakage is a specification for high impedance work

Five hundred picoamps sounds like nothing until it flows through a high impedance node. Into 1 Megohm it is 500 uV of offset, and into 10 Megohm it is 5 mV, which is larger than the signal in many sensor interfaces. The figure is also typical rather than maximum on the product page, so the tolerance budget has to be wider than the number printed. This is the reason the part is specified for precision circuits in the data sheet and also the reason a modern part with a leakage figure an order of magnitude lower exists. For a new board the leakage and the on resistance together point away from this generation; for a replacement in a 20 year old instrument, the DIP package and the pinout are the whole value.

Driving the control pins from modern logic

The control inputs are TTL and CMOS compatible, which historically meant 5 V logic. A 3.3 V processor driving this part is usually inside the threshold window but not guaranteed by the older data sheet, so a level check is worth doing before a board revision. The switching time is fast enough that the break before make action is what limits the multiplexer rate, not the logic rise time, and the charge injected into the signal path at each transition is the artefact that a high impedance following stage will show as a step.

Selection notes

  • The ADG212A is the same silicon with inverted control logic, useful when a processor drives several switches from one port and the sense has to be inverted.
  • Break before make is what makes the tied output multiplexer safe; a make before break part of this type would short two sources together.
  • The 44 V supply rating leaves 14 V of headroom over the signal range, which absorbs a supply transient without a clamp.
  • Single supply operation at 15 V removes the negative rail when the signal is unipolar, which is the common case in industrial control.

Questions buyers ask

Can four of these make a 4 to 1 multiplexer? Yes, with the four outputs tied together and one switch closed at a time. The break before make action is what keeps the tied node from shorting two inputs during the change.

Why is the part marked not recommended for new builds? The vendor has moved to lower resistance and lower leakage processes. The part remains in production for existing equipment, and a new board should select from the current switch families.

Replacement candidates with the same function are compared in how to verify a drop in replacement, and footprint equivalents are listed in pin to pin cross reference.

Request Quote — In Stock, 100% New & Original, Full Warranty