ADL5350ACPZ-R7
Product Specifications
ADL5350ACPZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADL5350ACPZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADL5350ACPZ-R7: A Mixer That Needs 4 dBm of Local Oscillator
The ADL5350ACPZ-R7 is a single ended, passive, up and down converting mixer built on a GaAs pseudomorphic high electron mobility process, with 6.8 dB of conversion loss, 25 dBm of input third order intercept and a local oscillator drive requirement of only 4 dBm typical. It is the part a base station receiver uses when the local oscillator has to be cheap and the blocker performance cannot be traded away. Buyers reach this page when a receiver front end has to survive a strong adjacent channel without a high power local oscillator amplifier.
What the part contains
A single ended mixer with broadband radio frequency, intermediate frequency and local oscillator ports, an integrated local oscillator amplifier, and no requirement for external baluns. The single ended architecture means the ports can be tuned to a band with simple external filter networks, and the local oscillator to radio frequency isolation is set by how well that network rejects the local oscillator, so a higher order filter buys more isolation. Supply is 3 V at 19 mA, the package is a 2 mm by 3 mm eight lead LFCSP, and the part is rated from -40 C to +85 C.
Key parameters
| Parameter | Value |
|---|---|
| Function | Up and down converting mixer, passive |
| Process | GaAs pseudomorphic high electron mobility |
| Ports | Single ended radio frequency, intermediate frequency and local oscillator |
| Conversion loss | 6.8 dB typical at 850 and 900 MHz |
| Noise figure | 6.5 dB typical |
| Input third order intercept | 25 dBm typical |
| Input compression point | 19 dBm typical |
| Local oscillator drive | 4 dBm typical |
| Supply | 3 V at 19 mA |
| Power | 57 mW |
| Package | 8-lead LFCSP, 2 mm by 3 mm |
| Temperature range | -40 C to +85 C |
What the numbers mean on a board
A conversion loss of 6.8 dB is a voltage ratio of 0.209, so a signal that arrives at 1 mW leaves at 0.209 mW. The published noise figure of 6.5 dB is 0.3 dB better than the loss, which is possible because the image termination and the local oscillator drive affect the two measurements differently, and it is the reason both numbers have to be read from the same condition in the data sheet rather than mixed. In a receiver chain the 6.5 dB is what goes into the cascade calculation, and it arrives before any gain stage, so it sets the noise floor of everything behind it.
Twenty five dBm of input third order intercept with only 4 dBm of local oscillator drive is the unusual combination. A conventional passive mixer with that linearity needs 17 to 20 dBm of drive, which means a driver amplifier and its current. Here the local oscillator amplifier is on the die and the drive requirement is 4 dBm, so the local oscillator chain saves a stage. The price is 19 mA at 3 V, which is 57 mW, and that is the trade: current in the mixer instead of current in a driver.
The 19 dBm compression point sets where the mixer stops being linear. With a 25 dBm intercept and a 19 dBm compression point, the useful dynamic range at the input is bounded by what the preceding filter and low noise amplifier can deliver. A blocker at 19 dBm is 89 mW, which is well above any signal a receiver should see, so the practical limit is the low noise amplifier in front of the mixer rather than the mixer itself.
Where it is used
- Cellular base station receive and transmit paths
- Point to point radio links
- Radio frequency instrumentation and spectrum analysers
- Repeaters and distributed antenna systems
- Receivers that need high blocker immunity at low local oscillator power
Sourcing notes and next step
Mixers are bought against a measured conversion loss and isolation, so the useful request to a supplier is the date code plus a promise of the electrical test rather than a price alone. The LFCSP body is 2 mm by 3 mm with a ground paddle that has to be soldered, and a part that is reflowed with voids under the paddle will show a conversion loss that is a decibel worse than the data sheet and a local oscillator leak that is worse still. The single ended ports also mean the external filter is part of the performance, so a substitute mixer with the same loss but different port impedance will not drop in.
Mixer, amplifier and filter options for a receiver front end are collected on the RF component sourcing page, and the cascade from low noise amplifier to mixer is covered in how to choose an RF amplifier. Parts with a long production commitment are listed on the obsolete and long life hub. Send the band, the local oscillator drive available and the quantity and we confirm stock and date code the same day.
Request Quote — In Stock, 100% New & Original, Full Warranty