ADG734BRUZ
Product Specifications
ADG734BRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG734BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG734BRUZ: four SPDT switches, 2.5 ohm typical, in one 20-lead TSSOP
The ADG734BRUZ is the quad SPDT of the ADG733/ADG734 family: four independently selectable changeover switches, 2.5 ohm typical on resistance, 0.5 ohm flatness, 100 pA leakage, guaranteed break before make. On a board that switches four channels between two paths it replaces four discrete changeover relays and the driver array behind them.
Published values
| Parameter | Value |
|---|---|
| Configuration | four independently selectable SPDT switches |
| Supply | 1.8 V to 5.5 V single, plus or minus 2.5 V dual |
| On resistance | 2.5 ohm typical, 4.5 ohm maximum at 25 C |
| Flatness | 0.5 ohm |
| Leakage | 100 pA |
| Switching | break before make guaranteed |
| Package | 20-lead TSSOP |
Relay replacement arithmetic
A signal relay of the size the ADG734 replaces draws tens of milliamps on its coil, needs a driver transistor and a catch diode, and takes milliseconds to move. The ADG734 draws below 0.01 microwatt, switches in nanoseconds and has no wear out mechanism at the contact. For a channel that changes state on every measurement cycle the relay is the wrong part on every count.
What a relay still does better is survive a fault: a mechanical contact tolerates a short and a surge that a 5 V CMOS switch does not. If the four channels can be connected to a field terminal, the switch needs series resistance and a clamp at the connector, and that protection is the engineering work the relay used to do for free.
Matching across the four channels
Four channels inside one package share one die and one process, so the channel to channel match is tighter than four separate packages can be. On a differential pair that is the number that matters: any mismatch between the two switches appears as common mode to differential conversion, and it is the reason to keep both legs of a pair in the same ADG734 rather than one switch per package.
Where it fits and where it does not
Four channel audio switching, data acquisition front ends that share one converter across four sensors, and battery powered instruments that cannot afford relay current. It does not fit a path that carries more than a few tens of milliamps: the continuous current rating of this family is set by the package and the bond wires, and a load that needs hundreds of milliamps belongs to the ADG1404 family instead.
The 2.5 ohm figure is typical. A build that needs the maximum over temperature and over the full signal range should work from 4.5 ohm and check the resulting error at the load impedance before the board goes out.
Sourcing notes for this family: how to verify a drop in replacement holds the cross references, the pin to pin cross reference is the pre substitution check, and component obsolescence management is what we use when the part on the drawing is not on the shelf.
Two questions buyers ask
Is the ADG734 available in a smaller package? The family is published in TSSOP and QSOP. The quad is the 20-lead TSSOP; a board that needs the same function in less area usually moves to a different family rather than to a smaller package of this one.
What is the analog input range on a 3 V rail? 0 V to 3 V. On resistance is specified up to 4.5 ohm maximum at 25 C on the 5 V rail and is higher on 3 V, so the error budget on a 3 V system should be built from the 3 V column and not from the 5 V typical.