Contact Us

ADG714BRUZ

Brand: Analog Devices
Analog Devices ADG714BRUZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG714BRUZ — Analog & Mixed-Signal ICs | Superb Automation

ADG714BRUZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG714BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADG714BRUZ: octal SPST switch with an SPI interface

The ADG714BRUZ puts eight independent single pole single throw switches behind a serial interface, in a 24-lead TSSOP. It uses an SPI, QSPI or MICROWIRE compatible bus, so eight switches cost four processor pins instead of eight, and it holds a 2.5 ohm on resistance with 0.6 ohm of flatness on a 2.7 V to 5.5 V single supply or a plus or minus 2.5 V dual supply.

Published values

ParameterValue
Configuration8 SPST switches, serially controlled
InterfaceSPI, QSPI and MICROWIRE compatible
On resistance2.5 ohm
On resistance flatness0.6 ohm
Leakage current0.1 nA
Supply range2.7 V to 5.5 V single, plus or minus 2.5 V dual
Power on resetall switches set to a defined state
Switching timesfast, quoted per supply
LogicTTL and CMOS compatible
Packages24-lead TSSOP and 24-lead LFCSP
SiblingADG715 uses an I2C interface

Serial control is the point of the part

Eight switches with individual control lines need eight processor pins and eight traces. The serial version uses a clock, a data line, a frame sync and a reset, and the switches are addressed by the bits shifted in. In a board with several octal switches the saving is not the pins, it is the routing and the number of layers needed to reach them.

The shift register also allows a pattern to be loaded and applied at once, so eight channels change state together rather than one after another. In a measurement front end that is the difference between a simultaneous sample and a sequence of samples taken at different times.

Power on reset and the safe state

The power on reset sets the switches to a defined state rather than leaving them random, which matters when the switches connect sources to a bus: a random pattern at power up connects several sources together before the processor has configured anything. That single feature is often the reason a serial switch is chosen over a parallel one.

The reset pin forces the same state without cycling the supply, so a fault recovery routine can return the analog path to a known condition without a power cycle. The 0.1 nA leakage is low enough that an off channel does not disturb a high impedance node.

2.5 ohm on a low voltage rail

The 2.5 ohm figure is the 5 V number, and the resistance rises at 3 V. Into a 10 kohm load that is 0.025 percent, so the switch is invisible in an instrument channel and significant only in a path that drives a low impedance. The 0.6 ohm of flatness is the ac term, and it sets the distortion floor of the switch at about 0.006 percent for a full swing.

A dual supply of plus or minus 2.5 V allows a bipolar signal to pass without a coupling capacitor, which is the configuration used for audio routing. The single supply range covers a 3.3 V system, and the logic inputs accept TTL levels so no level shifter is needed on the bus.

Where a customer needs a second position on this part, one stop BOM sourcing is the starting point, the obsolete part cross reference hub sets out the checks a substitution has to pass, and how to verify a drop in replacement is the short lead time route we quote against.

Two questions buyers ask

Can eight of these share one SPI bus? The interface has a frame sync input rather than a chip select per device in the usual sense, and each device needs its own sync line. What is shared is the clock and the data, which is where the pin saving comes from.

What state are the switches in at power up? The power on reset sets them to a defined state, and the reset pin can return them to it. That is what makes the part safe on a bus where several sources could otherwise be connected together.