ADG709BRUZ
Product Specifications
ADG709BRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG709BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG709BRUZ: 4-channel differential multiplexer on 1.8 V to 5.5 V
The ADG709BRUZ switches one of four differential inputs to a common differential output, which is the differential half of the ADG708 and ADG709 pair. It has a 3 ohm on resistance with 0.75 ohm of flatness, 100 pA of leakage, 14 ns switching times and a supply range from 1.8 V to 5.5 V single or plus or minus 2.5 V dual. It is qualified for automotive applications and comes in a 16-lead TSSOP.
Published values
| Parameter | Value |
|---|---|
| Configuration | 4 to 1 differential multiplexer, two poles |
| On resistance | 3 ohm typical |
| On resistance flatness | 0.75 ohm |
| Leakage current | 100 pA |
| Switching time | 14 ns |
| Supply range | 1.8 V to 5.5 V single, plus or minus 2.5 V dual |
| Addressing | 2-bit binary plus enable |
| Logic | TTL and CMOS compatible |
| Switching action | break before make |
| Qualification | automotive |
| Package | 16-lead TSSOP |
| Family | ADG708 is the 8 to 1 single ended version |
Differential switching halves the channel count and doubles the rejection
Four differential channels use eight switches, so the same silicon that gives eight single ended channels gives four differential ones. What the differential connection buys is rejection of whatever the two wires share: a ground offset between a sensor and the converter appears on both lines and is removed by the difference, while a single ended channel would read it as signal.
The two poles of one channel have to match, and the 0.75 ohm flatness figure is what makes the common mode rejection survive the switch. If one pole were an ohm higher than the other, a common mode voltage would convert into a differential error, and the rejection would fall as the common mode moved.
1.8 V operation and the 14 ns switch
A 1.8 V minimum supply means the part runs from the same rail as a low power microcontroller without a regulator, which is why it appears in portable instruments. The 14 ns switching time is fast enough to scan four channels between two conversions of a 200 kSPS converter, so the multiplexer does not set the scan rate.
The 100 pA of leakage is the figure that decides the source impedance. Into 1 Mohm it is 0.1 uV, into 10 Mohm it is 1 uV, and into 100 Mohm it is 10 uV, so a high impedance bridge is still comfortable and an electrometer input is not.
Enable and the shared bus
The enable input turns both poles off for all four channels, which is what allows several multiplexers to share one differential bus. Without it, the unselected devices would present their off capacitance and leakage to the line, and the selected channel would see a load it was not specified for.
The 2-bit address plus enable is the smallest control interface that can select four channels, so the part needs two processor pins and no decoder. That is the reason it is preferred over an eight channel single ended part in a system that already has a differential converter.
Buyers usually arrive at the ADC and DAC cross reference to find the family alternatives, then use the obsolete part cross reference hub to confirm a substitute before it is fitted; one stop BOM sourcing is the routine for a part that has already stopped shipping.
Two questions buyers ask
What is the difference between the ADG708 and the ADG709? The ADG708 is an eight to one single ended multiplexer and the ADG709 is a four to one differential multiplexer. They share the process, the supply range and the 16-lead package, and the control interface differs by one address line.
Can this part run from a 1.8 V rail and pass a 3.3 V signal? No. The signal range is limited by the supply, so a 3.3 V signal needs at least a 3.3 V rail on the switch. The 1.8 V rating describes the supply, not the signal.