ADG5409BRUZ
Product Specifications
ADG5409BRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG5409BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG5409BRUZ: four differential inputs switched to one differential output
The ADG5409BRUZ is the differential half of the ADG5408/ADG5409 pair. Four input pairs are switched to one output pair by a 2-bit address plus an enable, on the same trench isolated, latch up proof process as the single ended part. It is the order code for a bridge transducer, a differential current shunt or a twisted pair front end that has to be routed through one acquisition channel.
Published values
| Parameter | Value |
|---|---|
| Channels | 4 differential to 1 differential |
| Address | 2-bit binary plus EN |
| Supply | 9 V to 22 V dual, 9 V to 40 V single |
| Absolute maximum supply | 48 V |
| On resistance | 13.5 ohm typ |
| Channel match | 0.3 ohm typ at 25 C, 1.4 ohm max over temperature |
| Off isolation | -60 dB at 1 MHz |
| Supply current | 55 uA max |
| ESD | 8 kV human body model |
| Package and range | 16-lead TSSOP, -40 C to +125 C |
Why a differential switch is not two single ended ones
Two single ended channels can carry a differential pair, but the two dice are then separate and their on resistances are unrelated. The ADG5409 puts both halves of each pair on one die, which is why the channel match figure matters more here than the absolute on resistance.
The arithmetic is direct. A 0.3 ohm mismatch into a 10 kohm load carrying a 10 V common mode produces about 0.3 mV of differential error, which is a quarter of a 12-bit LSB on a 5 V reference. At 125 C the same mismatch limit is 1.4 ohm, so the error is about 1.4 mV, or one LSB. That is the number to check when a differential front end is asked to hold 12 bits over temperature.
The acquire window at the switch
The 2-bit decode means four channels, so a scan of all four takes four settling intervals. Turn on time is the same order as the single ended part, 140 ns typical, and the charge injection is shared with the family at 115 pC. Into a 1 nF hold capacitor that is 115 mV of step, which has to settle to a fraction of an LSB before the converter samples.
Because the output is one pair, the common node capacitance is charged by every channel that has been selected, so the settling after the last switch is the slowest of the scan. A buffer between the switch and the converter removes that dependency at the cost of its own offset drift.
Where the differential version is the right buy
Bridge transducers, thermopiles and isolated shunts all deliver a small differential signal on top of a common mode that can be several volts away from the local ground. Switching the pair rather than each leg keeps the common mode rejection of the front end intact, and the latch up proof process keeps that true when a transducer cable is plugged in while the card is off.
Avionics and automatic test equipment are the two places this order code is quoted most often. In both the switch sits between a connector and a converter, so the absolute maximum supply rating of 48 V and the 8 kV human body model rating on the pins are as much part of the specification as the on resistance.
Substitution and sourcing
A single ended part of the same family cannot replace this one on a differential front end, and a differential switch from a lower voltage family will fit the footprint while removing the overvoltage margin. The order of checks is supply span first, channel match at temperature second, charge injection third.
On a shortage the usual route is a family alternative with the same decode, then an acceptance test on the actual board rather than a data sheet comparison. The pages below cover the alternatives, the acceptance sequence and the case where the reel has already run out.
Buyers usually arrive at the pin to pin cross reference to find the family alternatives, then use the ADI second source page to confirm a substitute before it is fitted; component lead time solutions is the routine for a part that has already stopped shipping.
Two questions buyers ask
Does the ADG5409 need a separate logic supply? No. The logic thresholds are generated internally at 2.0 V high and 0.8 V low, so there is no VL pin and the part works with 3 V logic on any supply in the range.
What happens to the output when EN is low? All four channels switch off and the common output pair is left undriven, so the next stage has to provide its own bias path if a floating input is not acceptable.