Contact Us

ADG5208BRUZ

Brand: Analog Devices
Analog Devices ADG5208BRUZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG5208BRUZ — Analog & Mixed-Signal ICs | Superb Automation

ADG5208BRUZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG5208BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADG5208BRUZ: a latch-up proof 8 to 1 multiplexer rated to a 40 V single supply

The ADG5208BRUZ is the eight channel to one member of a family built for the case where a channel can be driven beyond the supply. It is latch-up proof, off source capacitance is 2.9 pF, off drain capacitance 34 pF, charge injection 0.2 pC, on resistance 160 ohm typical, and the supplies run from 9 V to 22 V dual or 9 V to 40 V single with a 48 V absolute maximum rating.

Published values

ParameterValue
Configuration8 single ended channels to 1 output
On resistance160 ohm typical
Off capacitance2.9 pF source, 34 pF drain
Charge injection0.2 pC
Supply9 V to 22 V dual, 9 V to 40 V single
Signal rangeVSS to VDD
Protectionlatch-up proof, 8 kV HBM input to supply
PackageTSSOP

Latch-up proof is a qualification answer, not a marketing phrase

A conventional CMOS switch that sees an input above its supply forward biases an internal junction. If the current is large enough the structure latches, the supply is shorted, and the part is destroyed when the rail collapses. A latch-up proof construction removes the four layer path, so an overvoltage at an input can still be outside the specification but it will not destroy the device in that way.

The electrostatic discharge rating is the second half of the same story: 8 kV human body model from an input to the supplies, 2 kV from input to input, 8 kV on all other pins. That is what makes the part usable on a connector that a technician can touch, where a 2 kV part would need external clamps on every channel.

24 V and 36 V systems

A 40 V single supply rating covers a 24 V industrial loop with headroom for a surge, and a 36 V rail directly. The same part is fully specified at 15 V, 20 V, +12 V and +36 V, so the resistance figure is published for the rails a real board uses rather than extrapolated from one.

The 160 ohm on resistance is high compared with a 4 ohm part, and that is the trade: the high voltage process and the protective structures cost resistance. Into a 10 kohm source it is 1.6 percent, which is acceptable on a 12 bit measurement; into a 1 kohm load it is 14 percent and dominates. This part belongs on the high impedance side of a system, in front of a buffer, not in series with a load.

Charge injection and capacitance at high voltage

0.2 pC is very low for a high voltage switch. Into a 1 nF hold capacitor it is a 0.2 mV step, and into 100 pF it is 2 mV. On a 10 V full scale that is one part in 5000, which suits a 12 bit measurement and is marginal for 16 bit without a settling delay.

The 34 pF off drain capacitance is the larger of the two and sits on the common output. Eight off channels put 8 times 34 pF, about 272 pF, in parallel with the selected path. That is a load the driving amplifier must be stable into, and on a 160 ohm switch it also sets a 43 ns time constant with the common node, so it is the capacitance rather than the resistance that dominates the settling.

Where it fits

Automatic test equipment, avionics, instrumentation that scans high voltage sensors, and communication systems with a 24 V or 36 V rail. For a 5 V system the resistance and the size are the wrong trade, and a 4 ohm part from the same family vocabulary is the better answer.

Where a customer needs a second position on this part, defense grade components is the starting point, medical device components sets out the checks a substitution has to pass, and the obsolete part cross reference hub is the short lead time route we quote against.

Two questions buyers ask

What does latch-up proof mean in practice? That an overvoltage at an input will not trigger the parasitic four layer structure that shorts the supply in a conventional CMOS switch. The part can still be damaged by excess current, so the external series resistance and clamp are still part of a protected input.

Can the ADG5208 run on a 5 V supply? No. The specified supply window starts at 9 V single and 9 V dual. A 5 V board is outside the range and needs a different part; the on resistance table is not valid below 9 V.