Contact Us

ADG451BRZ

Brand: Analog Devices
Analog Devices ADG451BRZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG451BRZ — Analog & Mixed-Signal ICs | Superb Automation

ADG451BRZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG451BRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADG451BRZ: quad SPST switch, 4 ohm, closed with a logic low

The ADG451BRZ contains four independently controlled single pole single throw switches in a 16-lead SOIC. Each switch is on when its control input is low, which is the opposite of the ADG452, and the four are otherwise identical. On resistance is 4 ohm with 0.2 ohm of flatness, the supply can reach 44 V, the analog signal range is the full plus or minus 15 V, and the part carries 100 mA of continuous current per channel.

Published values

ParameterValue
Configuration4 independent SPST switches
Control logicswitch closes with a logic low, the inverse of the ADG452
On resistance4 ohm
On resistance flatness0.2 ohm
Supply rangeup to 44 V total, specified at plus or minus 5 V, 12 V and plus or minus 15 V
Analog signal rangeplus or minus 15 V
Continuous current100 mA per channel
Turn on time70 ns
Turn off time60 ns
Power dissipation18 uW
ESD2 kV
Pin compatible withADG411, ADG412, ADG413, ADG431, ADG432, ADG433
Package16-lead SOIC_N

Normally closed is a system decision

A switch that is closed when its control line is low is the right choice when the safe state of the system is connected. A signal path that must stay alive while the controller is in reset, or a termination that must be present until a driver enables it, needs a switch that conducts with no power applied to the logic. The ADG451 does that and the ADG452 does the opposite, and the two are otherwise the same part.

Mixing them on one board is a real hazard. A line item that says ADG451 where the drawing expects ADG452 gives a channel that is on when the firmware thinks it is off, and the failure appears as a signal that cannot be muted rather than as a dead channel.

4 ohm and 0.2 ohm of flatness

Four ohms in series with a 1 kohm load is 0.4 percent of gain error, which is small enough for a 10-bit channel and not small enough for a 16-bit one. The flatness of 0.2 ohm is the term that matters for distortion: a switch whose resistance changes by 0.2 ohm across the signal swing modulates the signal by 0.02 percent, which is about -74 dB, and that is the distortion floor of the switch.

A 100 mA continuous rating is unusual for a signal switch and it is what allows the part to be used in a relay replacement for a small load, not only for a high impedance instrument input. The 70 ns turn on and 60 ns turn off are fast enough for a multiplexed channel at a few hundred kilohertz.

18 uW and the supply range

Eighteen microwatts is the quiescent dissipation, so the part adds nothing to a battery budget. The supply range of 44 V and the plus or minus 15 V signal range mean a channel that carries a high level analog signal needs no attenuation before the switch, which is the reason this family survives in test equipment.

The four switches share one supply and one ground, and the control inputs are TTL and CMOS compatible, so a 3.3 V processor can drive a plus or minus 15 V signal path without a level shifter. That combination, a low voltage control over a high voltage signal, is the part of the specification that most often decides the choice.

Sourcing notes for this family: the obsolete part cross reference hub holds the cross references, how to verify a drop in replacement is the pre substitution check, and vendor consolidation is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask

What is the difference between the ADG451 and the ADG452? The digital control logic is inverted. The ADG451 turns on with a logic low and the ADG452 with a logic high, and the analog behaviour is otherwise the same.

Can this switch carry a 100 mA load? Yes, 100 mA of continuous current per channel is specified. The on resistance of 4 ohm at that current dissipates 40 mW in the switch, which the package handles, and the voltage drop is 0.4 V.