ADG1636BCPZ-REEL7
Product Specifications
ADG1636BCPZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1636BCPZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADG1636BCPZ-REEL7: 385 mA Through a 1.6 Ohm Switch and the 0.616 V It Costs
The ADG1636 is two independent single-pole double-throw switches in one 16-lead LFCSP. Typical on resistance is 1 ohm, the maximum over temperature is 1.6 ohm, and flatness across the signal range is 0.2 ohm. The BCPZ body is rated for 385 mA of continuous current per channel. The same switch in a 16-lead TSSOP is rated 238 mA, because the exposed pad of the 4 mm by 4 mm body carries the heat.
What the order code fixes before the datasheet matters
BCPZ is the LFCSP, REEL7 is a 7 inch reel. A buyer comparing quotes on this part number against a TSSOP suffix is comparing two different current ratings, not two prices for the same thing. Both bodies share the switch, the enable pin and the break-before-make action, so the electrical behaviour is the same until the load current approaches the rating.
The published table, as the vendor states it
| Parameter | Value |
|---|---|
| Configuration | 2 x SPDT, independent, with EN |
| On resistance | 1 ohm typical, 1.6 ohm maximum over temperature |
| On resistance flatness | 0.2 ohm |
| Continuous current, LFCSP | 385 mA per channel |
| Continuous current, TSSOP | 238 mA per channel |
| Dual supply | plus or minus 3.3 V to plus or minus 8 V |
| Single supply | 3.3 V to 16 V |
| Logic threshold | VIH 2.0 V, VIL 0.8 V, 3 V compatible |
| Distortion | THD plus N 0.007 percent |
| Dissipation, static | below 16 nW |
Work the drop before the switch is chosen for a current path
At the 385 mA rating the part drops 0.616 V at the 1.6 ohm limit and 0.385 V at the typical 1 ohm. The dissipation inside the package reaches 0.237 W at that limit, which is why the LFCSP body is the one to take when the switch sits in a power path rather than in a signal path. At 238 mA the same resistance drops 0.381 V and dissipates 0.091 W. Put the switch in front of a 4 to 20 mA loop instead and the drop falls to 32 mV, so the same part is either a heat source or an invisible contact depending on the load the buyer intends.
Flatness is the figure that reaches the audio band
0.2 ohm of flatness against a 1 kohm load is 0.02 percent of gain, or 0.0017 dB, which is below the resolution of most bench measurements. Against a 50 ohm load the same flatness is 0.4 percent and becomes visible as distortion on a large signal. The vendor quotes THD plus N of 0.007 percent, or minus 83.1 dB, and that figure is tied to the flatness, not to the absolute resistance.
Selection notes
- No VL supply is required, the digital inputs are 3 V compatible from a 2.0 V threshold.
- Rail-to-rail operation, signal range extends to both supplies and the off state blocks up to the rails.
- Break-before-make action, so two channels can be tied to one node without a momentary short.
- Enable pin switches all channels off, which gives a defined state at power up.
Buyer questions
Is BCPZ interchangeable with the TSSOP version? Electrically yes, mechanically no, and the current rating differs: 385 mA against 238 mA. A board built for the TSSOP cannot take the LFCSP without a pad change, and a quote that swaps one for the other changes the current the customer can run.
Can it run from a single 3.3 V rail driven by 3 V logic? Yes. The single supply range starts at 3.3 V, VIH is 2.0 V and VIL is 0.8 V, so a 3 V driver switches it without a level shifter, and no separate logic rail is needed.
Family page for the category: Analog and mixed-signal ICs. For drop-in alternatives see pin-to-pin cross reference, and for multi-line BOM consolidation see BOM shortage recovery.
Request Quote — In Stock, 100% New & Original, Full Warranty