Contact Us

ADG1436YRUZ-REEL7

Brand: Analog Devices
Analog Devices ADG1436YRUZ-REEL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG1436YRUZ-REEL7 — Analog & Mixed-Signal ICs | Superb Automation

ADG1436YRUZ-REEL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG1436YRUZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADG1436YRUZ-REEL7: 260 mA per channel in the TSSOP body

The ADG1436YRUZ-REEL7 is a dual single-pole double-throw switch on the Analog Devices iCMOS process, in the 16-lead TSSOP. On resistance is 1.5 ohm, on-resistance flatness 0.3 ohm and channel-to-channel match 0.1 ohm. It is specified at plus or minus 15 V, 12 V and plus or minus 5 V, takes 3 V logic inputs, needs no separate logic supply, and passes signals rail to rail within the supplies. Switching is break-before-make. The part is listed in the analog and mixed-signal IC line card with the rest of the switch family.

Continuous current belongs to the package, not to the die

The datasheet gives two current ratings for the same circuit: up to 400 mA per channel in the 4 mm by 4 mm LFCSP and up to 260 mA per channel in the TSSOP. At 1.5 ohm the difference is arithmetic:

QuantityTSSOP at 260 mALFCSP at 400 mA
Voltage across the switch390 mV600 mV
Dissipation per channel101 mW240 mW
Dissipation, both channels203 mW480 mW
Gain error into 1 kohm0.15 percent0.15 percent
Gain error into 10 kohm0.015 percent0.015 percent
Flatness into 1 kohm0.03 percent0.03 percent
Channel match into 1 kohm0.01 percent0.01 percent

A 390 mV drop in a signal path is the number to check against the following stage, not the on resistance. In a 1 kohm load the flatness is 0.03 percent, which is below the 0.1 percent that most 12-bit paths can resolve; in a 100 ohm load it is 0.3 percent and the switch becomes part of the error budget.

Enable, break-before-make and what the TSSOP does not have

The EN input exists on the LFCSP package only. In the TSSOP order code the switch is always enabled and the only way to open both channels is to drive the two logic inputs, so a board that needs a hardware disable has to take the LFCSP. Break-before-make means the two throws are never connected at the same time, which is what allows the part to be used as a 2-to-1 multiplexer in front of an amplifier without a short across the two sources.

The logic inputs are 3 V compatible across the whole supply range, so a 3.3 V controller drives the part at plus or minus 15 V without a level shifter. A 10 pF load on the switch node gives a 15 ps time constant with 1.5 ohm, well below the switching time, so the settling of the stage behind it is set by the amplifier and not by the switch.

Selection notes

  • Match of 0.1 ohm between channels is a fifth of the flatness and a fifteenth of the absolute on resistance. In a gain-select pair the match is the specification that matters, because the two channels are compared against each other.
  • The dual SPDT arrangement gives two changeover switches, so a differential pair can be reversed with one logic line and both channels move together.
  • Signal range extends to the supplies in both directions, and in the off state the switch blocks levels up to the supplies. Signals above the supply are outside the part, unlike the fault protected members of the same family.
  • The YRUZ suffix is the TSSOP with the 260 mA rating. Substituting the LFCSP raises the current ceiling but changes the footprint and adds the enable pin.

Questions buyers ask

Can the two channels carry different currents? Yes, they are independent switches, but the package rating applies per channel and the total dissipation is the sum. Two channels at 260 mA in the TSSOP is 203 mW, which is the figure to put into a thermal check.

Is there a fault protected version? Yes, the ADG5413F and ADG5462F in the same 10 ohm family block plus or minus 55 V on the source pins with the supplies present or absent. They are a different die with a higher on resistance, so the choice is protection against 1.5 ohm of on resistance.

What should a quote request include? The order code, the package, the supply rails, the signal level and the load impedance behind the switch. Send the BOM line to the pin-to-pin cross reference if the part replaces an existing switch, and to the drop-in verification desk when the replacement has to be proven on the board before the reel is released.

Request Quote — In Stock, 100% New & Original, Full Warranty