AD5933YRSZ-REEL7
Product Specifications
AD5933YRSZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD5933YRSZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD5933YRSZ-REEL7: a 1 kohm floor, and what a 10 nF capacitor does to it
The AD5933YRSZ-REEL7 is a single chip impedance converter: a frequency generator, a 12 bit 1 MSPS analog to digital converter and a discrete Fourier transform engine on one die, read out over an I2C port. The generator excites an external impedance with a known frequency, the converter samples the response, and the DFT returns a real and an imaginary word for each frequency point in the sweep, so the host can work out magnitude and phase after a calibration step. The YRSZ body is the 16 lead SSOP, and the part is qualified for automotive use over minus 40 to plus 125 degrees C.
Buyers meet this part when a product has to measure impedance rather than voltage: corrosion probes, bio-impedance, electrolyte conductivity, moisture sensors, coil and material test. The two numbers that decide whether it fits are the excitation ceiling of 100 kHz and the impedance window, and the window is where quotations go wrong, because the first page quotes 1 kohm to 10 Mohm and the 100 ohm to 1 kohm extension needs parts that are not on the die.
What the vendor page states
| Parameter | Value |
|---|---|
| Converter | 12 bit, 1 MSPS, on chip |
| Excitation frequency | Programmable, up to 100 kHz |
| Frequency resolution | 27 bits, below 0.1 Hz |
| Impedance range | 1 kohm to 10 Mohm; 100 ohm to 1 kohm with additional circuitry |
| System accuracy | 0.5 percent |
| Temperature sensor | Internal, plus or minus 2 degrees C |
| Supply | 2.7 V to 5.5 V |
| Interface | I2C, with an internal system clock option |
| Output excitation | Programmable peak to peak amplitude |
| Body | 16 lead SSOP |
| Temperature | minus 40 to plus 125 degrees C, automotive qualified |
Where the frequency grid and the samples meet
The 27 bit frequency word is spread over the 100 kHz range, so one step is 0.000745 Hz, far finer than the crystal that clocks it. The useful limit is not the frequency resolution but the sample count per cycle: at 1 MSPS the converter takes exactly 10 samples in one cycle of a 100 kHz excitation, 100 samples at 10 kHz and 1,000 samples at 1 kHz. The DFT block works over 1,024 samples, so one frequency point costs 1.024 ms of conversion time whatever the excitation frequency is, and a 100 point sweep takes at least 102.4 ms before settling between points is counted. A 1,000 point sweep takes 1.024 s. Products that need a full spectrum four times a second are therefore outside what this part can do, and no amount of host software changes that.
The impedance window is the second constraint, and a capacitor makes it concrete. At 100 kHz a 1 nF capacitor is 1,591 ohm, comfortably inside the range; a 10 nF capacitor is 159 ohm and a 100 nF is 15.9 ohm, both below the 1 kohm floor and both needing the external current to voltage stage the vendor mentions. The 0.5 percent system accuracy is quoted for a calibrated range: 0.5 percent of 1 kohm is 5 ohm, but 0.5 percent of 10 Mohm is 50 kohm, so the top of the range is only meaningful when a calibration resistor of the same order is switched in. A specification written as 0.5 percent across the whole window is not what the silicon does.
Questions buyers ask before ordering
Does the 1 MSPS converter sample the excitation or the response? The response. The generator drives the unknown impedance and the converter samples what comes back, which is why the measurement is ratiometric against a calibration resistor and not an absolute voltage reading.
Can it measure below 1 kohm without extra parts? Not within the specified accuracy. The 100 ohm to 1 kohm band is an extension that needs an external amplifier, and a build that assumes the on chip circuit covers a 50 ohm sensor will read saturated codes.
Is the temperature reading good enough to compensate the impedance? The internal sensor is quoted at plus or minus 2 degrees C. That is enough to correct a coarse drift trend and not enough to correct a coefficient measured in parts per million, so precision work still needs an external sensor.
How this part is supplied
This reel sits in the Analog Devices analog and mixed signal range held for production builds, and converters that combine an acquisition block with a digital engine are grouped in the ADC and DAC cross reference by channel count, rate and body. Because the part is a system in one package, a shortage is rarely answered by a single substitute, and the practical route is a BOM shortage recovery review that looks at the whole measurement chain at once.
Request Quote — In Stock, 100% New & Original, Full Warranty