ADG1212YRUZ-REEL7
Product Specifications
ADG1212YRUZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1212YRUZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADG1212YRUZ-REEL7: four switches with one picocoulomb of charge injection
The ADG1212 contains four independently selectable single-pole single-throw switches built on the vendor's iCMOS process, and the ADG1212YRUZ-REEL7 order code reads Y for the industrial temperature grade, RU for the 16-lead TSSOP, Z for RoHS and REEL7 for the reel. The headline figures are a 1 pF off capacitance, a 2.6 pF on capacitance and charge injection below 1 picocoulomb, on a device that accepts a 33 V total supply range and is fully specified at plus or minus 15 V and at plus 12 V. Each switch conducts equally well in both directions, the signal range extends to the supplies, and no separate logic supply pin is needed because the digital inputs are 3 V logic compatible at 2.0 V high and 0.8 V low.
What the vendor page states
| Parameter | Value |
|---|---|
| Configuration | four independent SPST switches |
| On resistance | 120 Ohm |
| On capacitance | 2.6 pF |
| Off capacitance | 1 pF |
| Charge injection | below 1 picocoulomb |
| Supply | 33 V total range, specified at plus or minus 15 V and plus 12 V |
| Logic | 3 V compatible, 2.0 V high, 0.8 V low, no logic supply pin |
| Power dissipation | below 0.03 microwatt |
| Packages | 16-lead TSSOP and 3 mm by 3 mm LFCSP |
One picocoulomb into the hold capacitor
Charge injection is the error that a sample and hold circuit cannot calibrate out, because it appears at the moment the switch opens. One picocoulomb into a 1 nF hold capacitor is a 1 mV step, and into a 100 pF capacitor it is 10 mV. The direction of the step follows the control edge, so a differential sampling pair can cancel it if both switches are matched, and a single-ended channel cannot. That arithmetic sets the working rule for this part: the smaller the hold capacitor, the faster the acquisition and the larger the pedestal, and the datasheet curve for injection against supply voltage is the one to check at the actual rail rather than at nominal.
Where the 510 MHz figure comes from
Multiplying the 120 Ohm on resistance by the 2.6 pF on capacitance gives a 312 picosecond time constant, which corresponds to a 510 MHz corner. That is the number to quote when a customer asks whether the switch is fast enough for a video path or a wideband multiplexer, and it is far above any audio or instrumentation bandwidth. The off side behaves the other way: 1 pF at 1 MHz is 159 kOhm of reactance, so an off channel does not look like an open circuit at radio frequencies, it looks like a small capacitor, and feedthrough through that capacitance is what limits off isolation. Attenuation figures in decibels on the datasheet are frequency dependent for exactly this reason.
The logic polarity is the trap
The ADG1211 and the ADG1212 differ only in the digital control logic: the 1211 turns a switch on with a logic zero, the 1212 requires a logic one, and the ADG1213 mixes the two polarities and adds break-before-make action for multiplexing. A board that substitutes one member for another in a shortage keeps the same footprint and inverts every channel, which is a failure that only shows up at the system level. The device is also offered in an enhanced product version with a military temperature range of minus 55 C to plus 125 C and a controlled baseline for defense and aerospace programs, which is worth knowing when the requirement arrives with a drawing number. For data acquisition switching the analog to digital converter cross reference lists the converters that pair with this switch family, the pin to pin cross reference covers the polarity question by part number, and the analog and mixed signal category page holds the rest of the switch and multiplexer range.
Request Quote — In Stock, 100% New & Original, Full Warranty