Contact Us

AD9082BBPZ-2D2AC

Brand: Analog Devices
Analog Devices AD9082BBPZ-2D2AC is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD9082BBPZ-2D2AC — Analog & Mixed-Signal ICs | Superb Automation

AD9082BBPZ-2D2AC

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD9082BBPZ-2D2AC from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD9082BBPZ-2D2AC: the two DAC, two ADC build of the 12 GSPS MxFE

The AD9082BBPZ-2D2AC is the 2D2AC model of the AD9082 mixed signal front end, ordered in the 324-ball 15 mm by 15 mm BGA with a 0.8 mm pitch. The full device carries four 16-bit DACs at up to 12 GSPS and two 12-bit ADCs at up to 6 GSPS; the 2D2AC build populates two DACs and two ADCs, and the datasheet is explicit that the DAC3 and DAC4 output pins are unused on this model and should be tied to ground. Both converters reach 8 GHz of usable analog bandwidth and connect through 16 JESD204B or C lanes, eight transmit and eight receive.

Published values

ParameterValue
DAC cores on this modelTwo, 16 bit, up to 12 GSPS
ADC cores on this modelTwo, 12 bit, up to 6 GSPS
Analog bandwidth8 GHz usable on both directions
Serial lanes16 total, 8 JTx and 8 JRx
Lane rate24.75 Gbps JESD204C, 15.5 Gbps JESD204B
ADC performance at 6 GSPS, 2.7 GHz inNoise density minus 147.5 dBFS per Hz, noise figure 25.3 dB
ADC distortion at the same pointHD2 minus 72 dBFS, HD3 minus 68 dBFS, worst other minus 78 dBFS
DAC performance at 12 GSPS, 2.6 GHz outTwo tone IMD3 minus 72 dBc, single tone noise density minus 160 dBc per Hz, SFDR 75 dBc
DAC full scale current6.43 mA to 37.75 mA, programmable
Digital datapath8 fine and 4 coarse DUC, 8 fine and 4 coarse DDC, 48 bit NCO each
Receive equaliser192 tap programmable FIR
Package324-ball BGA, 15 mm by 15 mm, 0.8 mm pitch

The unused outputs are a real constraint

On the 2D2AC build the DAC3 and DAC4 output pins are present on the package and not connected to any converter, and the datasheet instructs that they be tied to ground if unused. That instruction is easy to skim past, and a board that leaves them floating inherits two unterminated output structures inside a package that is switching at 12 GSPS. A second consequence is that the power and decoupling around the package do not shrink with the model: the BGA and its supply network are the same, so the saving on the 2D2AC is on silicon and on lane count rather than on board area. A program that migrates from 4D2AC to 2D2AC keeps the same footprint and loses two transmit paths.

Where the bandwidth is actually needed

Eight gigahertz of usable bandwidth and a 12 GSPS DAC are aimed at direct to RF conversion in the C band and above, which is why the vendor lists wireless infrastructure, microwave point to point and E band, 5G millimetre wave, DOCSIS 3.1 and 4.0, phased array radar and electronic warfare, and test equipment. In a phased array the multichip synchronisation of the on-chip PLL is what allows several devices to keep a fixed phase relationship, and the fine DUCs with independent 48 bit NCOs are what put each element's signal on its own frequency without an external upconverter. In a test instrument the fast frequency hopping and the DDS blocks are the features that replace a synthesizer.

Lane count and the FPGA side

Sixteen lanes at 24.75 Gbps is 396 Gbps of raw serial capacity in one device, which sets the FPGA requirement as much as the converter does. The datapaths can be bypassed so the converter cores connect directly to the serialiser, which is the configuration for the widest instantaneous bandwidth and the highest lane count. Using the on-chip decimation and interpolation reduces the lane rate at the cost of latency and of the flexibility that a raw path gives. The TDD power saving option lets the transmit path be muted between slots without losing the JESD link, which is the feature that makes the part usable in a time division duplex radio rather than only in continuous transmit equipment.

Buying a device at this integration level

At this level the part number encodes a configuration rather than only a package, so the model suffix, the lane count and the temperature grade all have to be quoted together. The converter comparison work sits on the ADC and DAC cross reference, the second source position for wideband converters is described on ADI part second source, and the scheduling and allocation side for a BGA of this size is on the lead time page.