AD876JR
Product Specifications
AD876JR
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD876JR from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD876JR: 10 Bits at 20 MSPS for 160 mW From a Single 5 V Rail
The AD876JR is a CMOS analog to digital converter that samples at 20 MSPS with 10 bit resolution and dissipates 160 mW from a single 5 V supply. Those two numbers together are the reason it stayed in imaging and instrumentation assemblies long after faster converters appeared: a 20 MSPS converter that draws 160 mW can be repeated eight or sixteen times on one board without a thermal solution. Differential nonlinearity is 0.5 LSB and missing codes are guaranteed not to occur over the operating temperature range. The part includes a sample and hold amplifier, three state outputs that work with 5 V or 3.3 V logic, a standby mode, and force and sense reference inputs that remove the error caused by voltage drops in the reference distribution.
Published values
| Parameter | Value |
|---|---|
| Resolution | 10 bits |
| Throughput | 20 MSPS |
| Power dissipation | 160 mW |
| Supply | Single 5 V |
| Differential nonlinearity | 0.5 LSB |
| Missing codes | Guaranteed none |
| Input stage | Sample and hold, multistage pipelined with correction logic |
| Outputs | Three state, 5 V or 3.3 V logic compatible |
| Reference | Force and sense inputs, adjustable |
| Bodies | 28-lead SOIC, 28-lead SSOP, 48-lead TQFP |
Force and sense reference pins solve a board problem
At 10 bits and 20 MSPS the reference input draws current in bursts at the sampling rate, and the trace between the reference source and the converter has enough impedance at those frequencies to develop a voltage that changes with code. Force and sense pins let the reference be driven at one pin and measured at another, so the regulation loop closes at the converter rather than at the source. Boards that tie force and sense together at the source lose the benefit and show a code dependent gain error that looks like a converter linearity problem. It is also the first thing to check when a replacement converter appears less linear than the original.
Pipelined architecture and the latency question
A multistage pipelined converter delivers its result a fixed number of clock cycles after the sample, and that latency is deterministic. For a control loop this is fine as long as the loop is built around it, but for a system that expects the result in the same cycle as the sample request the latency appears as a timing error. The internal correction logic is what keeps the pipeline linear, and it is the reason differential nonlinearity is specified rather than inferred. When a board is retimed around a different converter, the pipeline depth is the parameter that changes the loop, not the sampling rate.
Logic levels and the 3.3 V interface
The digital outputs can be referred to a separate supply so that they talk to 3.3 V logic while the analog section stays on 5 V, which removes the level shifters that would otherwise sit between the converter and a modern processor. The three state control allows several converters to share a bus, which is how multi channel imaging boards with one converter per channel were built before serial interfaces became fast enough. If the output supply is left at 5 V while the receiver is 3.3 V tolerant only, the interface works on the bench and fails at temperature, because the absolute maximum on the receiver input is exceeded for part of each cycle.
Standby mode and the system level power budget
A standby mode that drops the converter to a fraction of its running current is useful in an instrument that samples in bursts, and it is the reason the part appears in portable imaging devices. The recovery time from standby is the number that decides whether the mode is usable, because a converter that takes milliseconds to return to specified accuracy cannot be parked between closely spaced bursts. The same applies to the reference, which has to be stable before the first conversion after wake up, and that settling time is often longer than the converter's own.
Keeping a 20 MSPS converter available
This generation of converters is still in production in some bodies and gone in others, so a build that needs it should check the body first. The 28-lead SOIC is the easiest to place and the TQFP is the version most likely to be limited. A substitute has to match the reference arrangement, the output supply and the pipeline latency, and matching only the resolution and the rate is not enough. The converter cross reference page groups the parts we hold by rate, resolution and body, the ADI part second source page covers grade equivalents, and the lead time page shows what is on the shelf now.