Contact Us

AD8657ARMZ

Brand: Analog Devices
Analog Devices AD8657ARMZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8657ARMZ — Analog & Mixed-Signal ICs | Superb Automation

AD8657ARMZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8657ARMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8657ARMZ: dual 18 volt micropower amplifier at 22 microamps per channel

The AD8657ARMZ is the two channel member of the AD8657/AD8659 family in an 8-lead MSOP body. It runs from 2.7 V to 18 V, draws 22 uA maximum per amplifier and still holds a 350 uV maximum offset with rail-to-rail input and output, which is the shape of a battery instrument or a loop powered sensor that has to measure a high voltage rail.

Published values

ParameterValue
Offset voltage350 uV maximum over the common mode range
Offset voltage drift2 uV/C
Input bias current5 pA typical, 20 pA maximum
Supply current per amplifier18 uA typical, 22 uA maximum
Gain bandwidth230 kHz at a gain of 100
Slew rate80 V/ms, 75 V/ms at 10 V
Settling time to 0.1 percent15 us on a 1 V step
Voltage noise density50 nV/root Hz at 1 kHz, 5 uV p-p over 0.1 to 10 Hz
CMRR94 dB minimum on 18 V, 88 dB minimum on 10 V
Input voltage range0 V to 18 V on an 18 V supply, rail to rail
Output swing17.97 V minimum high into 100 k
Short circuit current12 mA
Phase margin60 degrees
Supply range2.7 V to 18 V single supply, +-1.35 V to +-9 V dual

22 microamps over a year

22 uA for a year is 193 mAh, and two channels are 385 mAh, so a 2 Ah coin cell stack lasts five years with the amplifier as the only load and less once a converter and a reference are added. That is the whole point of the part: at 18 V a conventional CMOS amplifier draws 1 mA to 2 mA, which is fifty times more, and a 1 mA load would flatten the same cell in months.

The cost is speed. 230 kHz at a gain of 100 is 2.3 kHz of closed loop bandwidth at that gain, and the slew rate of 80 V/ms means a 10 V step takes 125 us. A channel sampled at 10 SPS does not care; a channel that has to follow a 1 kHz signal cannot use this amplifier at all.

Rail-to-rail input on an 18 V supply

The input common mode range is the full 0 V to 18 V, which is unusual on a high voltage part and is the reason the device is used for high side sensing. A 12 V battery stack, a 15 V rail or a 0 V to 10 V industrial signal all sit inside the window, so the amplifier can be a follower on a rail that a 5 V part could not touch.

The output reaches 17.97 V minimum into 100 k, which is 30 mV below the rail, so a follower on an 18 V supply reproduces an 18 V input to within 30 mV. At 1 mA of load the swing is smaller, and at 12 mA of short circuit the output is a protection limit rather than an operating point.

Noise and settling at this current

50 nV/root Hz is a micro-power number and it has to be read against the bandwidth the channel needs. Over a 10 kHz band it is 5 uV rms, which is 7 codes of a 16-bit converter on 18 V; over a 100 Hz band it is 0.5 uV rms, which is under one code. Filter the input to the bandwidth the measurement actually needs and the part stays usable at 16 bits.

The 15 us settling to 0.1 percent on a 1 V step sets the channel rate: a scanner that gives each channel 100 us has room, one that switches in 5 us does not. The 60 degrees of phase margin leaves a stable loop with modest capacitive loads, and the series resistor to a converter's sampling capacitor should be sized for that, not for speed.

Two pages worth reading before a purchase order goes out are component lead time solutions and defense grade components; the first lists what else fits the socket, the second is the test sequence for a drop in, and how to verify a drop in replacement covers the case where the shortage is already on the line.

Two questions buyers ask

Can the AD8657ARMZ run directly from a 12 V or 15 V rail? Yes. The supply range is 2.7 V to 18 V and the input range covers the full supply, so a 12 V or 15 V system needs no pre-regulator for the amplifier.

Is it fast enough for a 1 kHz signal? At a gain of 1 the 230 kHz bandwidth allows it; at a gain of 100 the closed loop bandwidth is 2.3 kHz and a 1 kHz signal at full amplitude is at the edge. The 80 V/ms slew rate is the harder limit on large signals.