Contact Us

AD8602ARMZ

Brand: Analog Devices
Analog Devices AD8602ARMZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8602ARMZ — Analog & Mixed-Signal ICs | Superb Automation

AD8602ARMZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8602ARMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8602ARMZ: two 8 MHz CMOS amplifiers in an 8-lead MSOP

The AD8602ARMZ is the two channel member of the AD8601/AD8602/AD8604 family in an 8-lead MSOP: 8.4 MHz of gain bandwidth, 6 V/us of slew rate, a 500 uV maximum offset at room temperature and 33 nV/root Hz of noise for 750 uA per amplifier. It is a wideband general purpose dual that fits where a 1 MHz part would be too slow and a 20 MHz part would be too hungry.

Published values

ParameterValue
Offset voltage, A grade80 uV typical, 500 uV maximum at 25 C, 1300 uV maximum over temperature
Offset voltage drift2 uV/C typical
Input bias current0.2 pA typical, 60 pA maximum, 1 nA maximum at 125 C
Supply current per amplifier750 uA typical, 1.2 mA maximum at 5 V
Gain bandwidth8.4 MHz at 5 V, 8.2 MHz at 3 V
Slew rate6 V/us at 5 V, 5.2 V/us at 3 V
Voltage noise density33 nV/root Hz at 1 kHz
Open loop gain30 V/mV minimum
Settling to 0.01%under 1 us at 5 V
Phase margin55 degrees at 5 V
Thermal resistance, MSOP-8142 C/W junction to ambient
Supply range2.7 V to 5.5 V single supply

Eight megahertz against 55 degrees of phase margin

8.4 MHz of gain bandwidth and 6 V/us make this part usable in a 500 kHz signal path, but 55 degrees of phase margin is the number that decides whether it works there. A load capacitance of 200 pF at unity gain cuts that margin roughly in half and a 1 nF load will oscillate. Keep the load under about 100 pF, or isolate the output with a 50 to 100 Ohm resistor and take the feedback from the amplifier side.

The same figure explains why this part is specified with a 2 kOhm load: at 2 kOhm the output stage is already working, and a 600 Ohm load will push the open loop gain down and move the closed loop response.

What 500 microvolts means against a 12-bit converter

At 5 V a 12-bit code is 1.2 mV, so a 500 uV maximum offset is less than half a code at room temperature and about one code at 125 C, where the guaranteed maximum rises to 1.3 mV. That is a usable combination for a 12-bit channel and a marginal one for 16 bits, where a code is 76 uV and the offset is seven codes. The drift line of 2 uV/C is what limits an uncalibrated 16-bit channel to a few codes over a normal operating range.

Reading the offset table properly

The sheet publishes two offset columns for this family: one with the input held between 0 V and 1.3 V on a 3 V rail, and one across the full input range. The mid range figure is 80 uV typical, the full range figure is 350 uV typical, and the difference is the crossover of the rail-to-rail input stage. A channel that measures a small signal sitting near mid supply gets the good number; a channel that swings across the whole range gets the larger one.

Where it is used

Active filters up to a few hundred kilohertz, four to twenty channel data acquisition front ends, photodiode transimpedance stages in the tens of kilohertz, and buffer amplifiers ahead of a 12-bit converter running at a few hundred kilo samples per second. Above 1 MHz of signal the 20 MHz and 24 MHz families on the cross reference page are the next step.

Sourcing notes for this family: the amplifier cross reference holds the cross references, the ADC and DAC cross reference is the pre substitution check, and the pin to pin cross reference is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask

Does the AD8602ARMZ need a compensation capacitor? No. It is unity gain stable, but the 55 degree phase margin means a capacitive load above about 100 pF should be isolated with a series resistor.

How much current do both channels draw at 3.3 V? About 1.4 mA typical for the pair, since the per amplifier figure falls to 680 uA at 3 V.