Contact Us

AD8370AREZ

Brand: Analog Devices
Analog Devices AD8370AREZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8370AREZ — Analog & Mixed-Signal ICs | Superb Automation

AD8370AREZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8370AREZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8370: 40 dB of Digitally Set Gain From LF to 750 MHz in Two Overlapping Ranges

The AD8370 is a digitally controlled variable gain amplifier with a differential input of 200 ohms, a differential output of 100 ohms, a bandwidth of 750 MHz at the 3 dB point, and a gain range selected by the most significant bit of an eight bit serial word. The low range runs from -11 dB to +17 dB and the high range from +6 dB to +34 dB, which overlap by 11 dB and together give 45 dB of span. It runs from a single supply of 3 V to 5 V and drops below 4 mA in power down.

Two ranges, and the choice between them is a noise decision

The two ranges are 17 dB apart, and the overlap means that most gain settings can be reached in either range. The high range gives a noise figure of 7 dB at maximum gain and the best distortion at the top of its span; the low range gives a lower gain with the input stage run at a different operating point. For a receiver front end the high range is used until the signal is strong enough that distortion matters more than noise, and then the part is switched to the low range and the gain is made up again. That switch is the only discontinuity in the gain curve, and it should be placed where the signal level makes it inaudible or invisible to the demodulator.

The serial word and what it does

ParameterValueNote
Frequency rangeLow frequency to 750 MHz3 dB bandwidth, usable well below that for flatness
Low gain range-11 dB to +17 dB128 steps, better than 2 dB resolution
High gain range+6 dB to +34 dB128 steps, better than 1 dB resolution
Noise figure7 dB at maximum gainDegrades as the gain is reduced
Output intercept+35 dBm at 70 MHzTwo tone, at the gain setting quoted
Supply3 V to 5 V single railPower down below 4 mA, gain setting retained

Different impedances on the two ports

A 200 ohm input and a 100 ohm output mean the part is also a 2 to 1 transformer, which is convenient when driving a filter that wants a lower impedance than the source, and inconvenient when the source is already 50 ohms single ended. The input is differential, so a balun or an active single ended to differential stage is required, and that stage contributes its own noise ahead of the 7 dB figure. In a receiver the balun loss, typically 0.5 to 1 dB, has to be added before the cascade calculation is done.

Power down that keeps the setting

The part powers down through a dedicated pin and retains its gain setting while down, drawing under 4 mA. That makes it usable as a channel switch as well as a gain control, with the caveat that the input to output isolation in power down is not the same as a real switch, and the impedance presented to the preceding stage changes. Where a channel has to be isolated from a shared bus, a switch is still the right part.

Availability and substitutes

A replacement for a digitally controlled amplifier has to match the interface before it matches the gain range, because firmware that writes an eight bit word to a shift register will not drive a part with a parallel or a voltage control. The amplifier cross reference page lists the variable gain family, the ADC DAC cross reference page covers the converters that follow it, and footprint checks are on the pin to pin cross reference page.