AD827JRZ
Product Specifications
AD827JRZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD827JRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD827JRZ: 50 MHz, 300 V per us and 120 ns to Settle
The AD827JRZ is a dual high speed amplifier with 50 MHz of unity gain bandwidth, 300 V per microsecond of slew rate and 120 ns of settling time, and it adds one property that the rest of the family does not have: an open loop gain of 3500 V per volt into a 500 ohm load. That combination is what makes it usable as a video amplifier with real gain accuracy, because a stage running at a gain of two or five does not lose its output swing to finite open loop gain. Differential gain is 0.04 percent at 4.4 MHz with 0.198 degrees of differential phase, offset is 2 mV maximum with 15 uV per degree of drift, and the total supply current for both amplifiers is 10 mA.
Published values
| Parameter | Value |
|---|---|
| Configuration | Dual, unity gain stable |
| Unity gain bandwidth | 50 MHz |
| Slew rate | 300 V per microsecond |
| Settling time | 120 ns |
| Open loop gain | 3500 V per volt into 500 ohm |
| Differential gain | 0.04 percent at 4.4 MHz |
| Differential phase | 0.198 degrees at 4.4 MHz |
| Input offset voltage | 2 mV maximum |
| Offset drift | 15 uV per degree Celsius |
| Supply current | 10 mA total for both amplifiers |
Open loop gain and the gain stage that will not sag
In a video distribution chain the signal passes through a gain of two or a cable equaliser, and an amplifier with modest open loop gain produces a closed loop gain that is a few tenths of a percent low and that changes with output level. That shows up as a compression of the brightest part of the picture, which is hard to diagnose because the amplifier is not clipping. At 3500 V per volt into 500 ohm the closed loop error at a gain of two is small enough to ignore for an 8 bit or 10 bit signal path, and the same property keeps a filter stage's response close to the calculated curve instead of drooping at the band edge.
Ten milliamps for both channels changes the board budget
Ten milliamps total for two amplifiers is a low figure for a 50 MHz part and it is achieved by accepting a slew rate of 300 V per microsecond rather than the 350 of the faster sibling. On a 15 V rail the package dissipates about 150 mW with both channels running, so an array of four packages on one board is still inside a passive thermal budget. That is the number that matters in a video router or a multi channel instrument, where the choice is often between a faster part that needs airflow and a slightly slower one that does not.
Bodies, grades and the cerdip detail
The J grade in the 8-lead plastic DIP is the common commercial version, and the same device is sold in a cerdip for higher temperature work, in a 16-lead small outline body and in a 20-lead leadless chip carrier. The four bodies are not interchangeable on a finished board, so a grade or temperature upgrade in a mature assembly is a body change unless the 16-lead outline was used from the start. Tape and reel availability to EIA-481A matters for automatic placement, and a reel that is not to that standard will jam a feeder even though the parts are electrically identical.
Replacing a video amplifier without touching the filter
Video stages are usually tuned around the amplifier's own input capacitance and output impedance, so a substitution that changes either one shifts the response of the reconstruction filter. The safe path is to keep the same body and the same pinout and to compare open loop gain, output drive and differential gain and phase against the original. Where the exact grade is gone, a higher grade in the same body is normally the cheapest answer, and a family member with different bandwidth is the answer of last resort because it moves the filter. The amplifier cross reference page groups the video capable parts by open loop gain and body, the ADI part second source page lists the grade equivalents, and the obsolete part cross reference hub covers the case where the commercial grade has already stopped.