AD822ARZ
Product Specifications
AD822ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD822ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD822ARZ: Two FET Input Amplifiers, Rail to Rail Output, 5 V to 30 V
The AD822ARZ is the dual version of the single supply FET input amplifier family, and it keeps the two properties that make that family useful: the input common mode range extends below ground and the output swings to both rails. On a single 5 V supply that combination lets a two stage signal chain handle a sensor that sits at ground while the converter it feeds expects a full scale span from zero to 5 V, with no negative rail anywhere on the board. Unity gain bandwidth is 1.8 MHz, slew rate is 3 V per microsecond, input bias current is 25 pA maximum, and voltage noise is 13 nV per root hertz at 10 kHz. Each amplifier delivers 15 mA minimum, and the part is stable with capacitive loads up to the published limit without an external isolation resistor.
Published values
| Parameter | Value |
|---|---|
| Configuration | Dual, independent amplifiers |
| Supply | Single 5 V to 30 V |
| Output swing | Rail to rail |
| Input common mode | Extends below ground |
| Unity gain bandwidth | 1.8 MHz |
| Slew rate | 3 V per microsecond |
| Input bias current | 25 pA maximum |
| Voltage noise | 13 nV per root hertz at 10 kHz |
| Output current | 15 mA minimum per amplifier |
| Bodies | 8-lead PDIP, MSOP and SOIC |
No phase inversion is a specification worth reading twice
Many single supply amplifiers invert their output when the input is driven below the negative rail, so a signal that overshoots ground appears at the output as a rail to rail excursion of the wrong polarity and the following stage latches. The AD822 is specified not to invert under that condition, and combined with the input range that extends below ground it means an input transient that dips negative produces a clipped but correctly signed output. For an instrument that survives a probe short to a negative supply this is the difference between a recoverable event and a damaged converter, and it is one of the reasons the part stays in medical and process control assemblies long after faster devices have become available.
Matching the two channels
A dual amplifier is only cheaper than two singles if the two halves can share a reference and a supply without interfering. In this part the two amplifiers share the supply pins and nothing else, so crosstalk is limited to what couples through the supply impedance. At 1.8 MHz the supply rejection falls with frequency, so the channel separation depends on the decoupling network rather than on the die. Placing a 100 nF capacitor within a few millimetres of the package and a 10 uF bulk capacitor at the point where the two channels share a rail keeps the separation where the data sheet puts it. Sharing one decoupling capacitor between two packages is the usual way this goes wrong in a cost reduction.
When the 1.8 MHz bandwidth is enough and when it is not
For a 12 bit converter sampling at 100 kSPS the buffer needs to settle within the acquisition window, and 1.8 MHz with 3 V per microsecond is adequate when the step size is under a volt. At higher throughput or larger steps the settling tail dominates and the last bits are lost. The honest way to choose is to compute the settling time to half an LSB at the converter resolution and compare it with the acquisition window, not to compare bandwidths. Where the numbers do not fit, the same family has members with more bandwidth and the same input structure, and moving between them keeps the input network unchanged because the bias current and the input range are the same.
Bodies, grades and the supply question
The part comes in PDIP, MSOP and SOIC, and the MSOP is the body that has to be checked first when a build is being rescheduled, because it is the version tied to the highest volume programs. All three are specified over the industrial temperature range in the A and B grades. The supply window of 5 V to 30 V means a board that runs from a 24 V loop can power the amplifier directly, but the dissipation at 30 V with a 15 mA load is high enough that the package thermal resistance becomes the limit rather than the amplifier. The amplifier cross reference page lists the dual FET input options by bandwidth and body, the ADI part second source page shows the grade equivalences, and the lead time page covers what can be shipped against a schedule that has already slipped once.