AD8226ARZ-R7
Product Specifications
AD8226ARZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8226ARZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8226ARZ-R7: a wide supply instrumentation amplifier with a gain range of 1 to 1000
What this order code is
AD8226ARZ-R7 is a single instrumentation amplifier that sets any gain between 1 and 1000 with one external resistor. The supply range is 2.2 V to 36 V single ended or plus and minus 1.35 V to plus and minus 18 V, the output swings rail to rail, and the input common mode range extends below the negative supply, so a small signal near ground can be amplified on a single rail. The quiescent current is 350 microamps typical and the part is specified over minus 40 C to plus 125 C in an 8-lead SOIC or MSOP body.
Two features matter more than the headline numbers. The inputs are protected beyond the supplies: with a plus and minus 5 V supply the part is guaranteed to survive plus and minus 35 V at the input without damage, which is what allows it to sit on a real sensor cable. Minimum and maximum input bias current are both specified, which exists so that an open wire can be detected by the bias current going to zero rather than by a second circuit.
Parameters as published
| Item | Value |
|---|---|
| Gain range | 1 to 1000, one external resistor |
| Single supply range | 2.2 V to 36 V |
| Dual supply range | plus and minus 1.35 V to plus and minus 18 V |
| Bandwidth at a gain of 1 | 1.5 MHz |
| Common mode rejection at a gain of 1 | 90 dB minimum, B grade models |
| Input voltage noise | 22 nV per root hertz |
| Supply current | 350 microamps typical |
| Input range | extends below the negative supply |
| Input protection | plus and minus 35 V on a plus and minus 5 V supply |
| Output swing | rail to rail |
| Body | 8-lead SOIC, MSOP also available |
| Temperature range | minus 40 C to plus 125 C |
Numbers that decide the application
The published 1.5 MHz bandwidth belongs to a gain of 1. The same part at a gain of 100 has about 15 kHz and at a gain of 1000 about 1.5 kHz, so a 1 kHz bridge signal at a gain of 1000 is close to the limit of the amplifier and not to the limit of the sensor. The 22 nV per root hertz is referred to the input: over a 1 kHz band it is 0.7 microvolts RMS, over 10 kHz it is 2.2 microvolts, and at a gain of 100 the 2.2 microvolts becomes 220 microvolts at the output, which is a fifth of a 16 bit least significant bit on a 5 V range.
The common mode figure needs care before it is used in a comparison. The 90 dB minimum at a gain of 1 is attached to the B grade models, and this order code is the A grade, so the number to work to is the A grade column in the data sheet table and not the family headline. At 90 dB a 10 V common mode leaves 316 microvolts of referred error, which is larger than the offset of most sensors in this class, so the gain and the bridge balance decide the error long before the amplifier does.
The supply range is the real differentiator. At 36 V single ended the part runs directly from a 24 V industrial rail with margin for a plus 20 percent excursion and still costs 350 microamps, which is 12.6 mW at the top of the range and about 1.2 mW at 3.3 V. The input protection of plus and minus 35 V on a plus and minus 5 V supply is 7 times the supply, so a miswired transducer or a hot plug event on a signal cable does not destroy the front end.
Where it fits and where it does not
It fits 4 to 20 mA loop receivers, bridge and strain gauge front ends, thermocouples, plus and minus 10 V industrial signals and any channel that lives on a 24 V rail. It does not fit a 24 bit absolute measurement, a channel that needs more than about 15 kHz at a gain of 100, or a board where the input can be driven outside the specified protection window. The minimum gain of 1 with a rail to rail output is unusual for a low cost instrumentation amplifier, and it is why the part can also be used as a difference amplifier on plus and minus 10 V signals.
Supply and second source questions
The questions we get on this code are about grade, body and the input protection, and about whether a lower priced instrumentation amplifier in the same footprint will meet the common mode range at the actual gain. A part that meets 90 dB at a gain of 1 is not automatically the same part at a gain of 100, and a part that is pin compatible is not automatically protected to plus and minus 35 V. The members that share the die and the ones that only look similar are listed on the amplifier cross reference page.
Sourcing notes and next step
We quote this code against the bill of materials and check gain resistor value, body, grade and packing, because the A and B grades are not interchangeable in a channel that was specified around the B grade common mode figure. Where the exact code is short we will say so rather than substitute a similar part number. Send the line items, quantities and required date through the BOM shortage recovery page, and if the channel is on a long life industrial platform, the alternative route is the obsolete part cross reference hub, which is where we track the parts that are still in production but no longer recommended for new builds.
Request Quote — In Stock, 100% New & Original, Full Warranty