AD8225ARZ
Product Specifications
AD8225ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8225ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8225ARZ: Fixed Gain of Five, No External Components
The AD8225ARZ is an instrumentation amplifier with a gain fixed at five by trimmed internal resistors. There is nothing to fit and nothing to match, which is the point: a 4 to 20 mA receiver or a bridge front end built with this part has no gain resistor to drift, no ratio to match and no tolerance to budget beyond the amplifier's own. It draws 1.2 mA maximum, runs from 1.7 V to 18 V, delivers 86 dB minimum common-mode rejection at DC and 80 dB minimum to 10 kHz, has a 900 kHz bandwidth, a 5 V per microsecond minimum slew rate, 150 microvolts maximum input offset with 2 microvolts per degree maximum drift, and 5 parts per million per degree maximum gain drift.
Published values
| Parameter | Value |
|---|---|
| Gain | 5 V per V, fixed by internal trimmed resistors |
| Supply range | 1.7 V to 18 V, single or dual |
| Supply current | 1.2 mA maximum |
| Common-mode rejection | 86 dB minimum at DC, 80 dB minimum to 10 kHz |
| Bandwidth | 900 kHz |
| Slew rate | 5 V per microsecond minimum |
| Input offset voltage | 150 microvolts maximum |
| Offset drift | 2 microvolts per degree Celsius maximum |
| Gain drift | 5 parts per million per degree Celsius maximum |
| Input bias current | 1.2 nA maximum |
| Package | 8-lead SOIC |
Five parts per million of gain drift is the headline
A gain resistor network built from 25 parts per million resistors drifts by about 25 parts per million per degree before any tracking is considered, and two resistors that drift in opposite directions make it worse. The internal network is trimmed on the die and drifts at 5 parts per million per degree maximum, which over 100 degrees is 0.05 percent of gain. For a 4 to 20 mA loop that has to hold 0.1 percent accuracy across the industrial temperature range, that difference decides whether the board needs a calibration step in production. The offset drift of 2 microvolts per degree is the second term: at a gain of 5 that is 10 microvolts per degree at the output, which over 100 degrees is 1 mV, or 0.02 percent of a 5 V full scale.
The 1.7 V supply is not a typo
Running from 1.7 V to 18 V covers a single lithium cell, a 5 V rail, a 12 V industrial rail and a 15 V dual supply without a change. At the low end the input common-mode range and the output swing both shrink towards the rails, and the 900 kHz bandwidth is specified at a higher supply. In a 3 V system the part still delivers its DC accuracy, and the swing is limited by the output stage rather than by the input. The reason the wide range matters commercially is that one order code covers several product variants, which is exactly the situation where a fixed gain part beats a resistor-set one.
Where it fits and where it does not
Patient monitors, current transmitters, 4 to 20 mA converters and bridge transducers are the listed applications, and the common thread is a signal that needs exactly one gain and has to stay stable without calibration. It does not fit where the gain has to change per channel, where the source needs more than 86 dB of rejection, or where the input has to go to the positive rail. For those, a resistor-set part with a wider common-mode range is the answer, and the trade is one more component and one more tolerance in the budget.
Availability and second sourcing
A fixed gain of five with internal resistors cannot be replaced by a resistor-set part without adding components and recalibrating, so the practical substitute is another fixed gain part with the same gain and pinout. The amplifier cross reference page lists the fixed gain instrumentation amplifiers, the pin to pin cross reference page covers the 8-lead outlines, and the verification checklist is the sequence to run on a candidate.