AD820ARZ
Product Specifications
AD820ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD820ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD820ARZ: A FET Input Op Amp That Works Below Its Own Negative Rail
The AD820ARZ is a single supply FET input amplifier, and the feature that separates it from the rest of the single supply market is that the input common mode range extends below ground. On a single 5 V rail that means the amplifier can look at a signal that goes slightly negative without a charge pump and without a second supply. Quiescent current is 800 uA maximum, unity gain bandwidth is 1.8 MHz, and the input bias current is 25 pA maximum at room temperature, which is the number that makes the part usable with high impedance sources such as photodiodes and pH probes. Offset is 800 uV maximum, voltage noise is 13 nV per root hertz at 10 kHz, and the output drives 350 pF of load capacitance with 15 mA minimum of output current.
Published values
| Parameter | Value |
|---|---|
| Supply | Single 5 V to 30 V |
| Input common mode | Extends below ground |
| Quiescent current | 800 uA maximum |
| Unity gain bandwidth | 1.8 MHz |
| Input offset voltage | 800 uV maximum |
| Input bias current | 25 pA maximum |
| Voltage noise | 13 nV per root hertz at 10 kHz |
| Capacitive load | 350 pF |
| Output current | 15 mA minimum |
| Bodies | 8-lead PDIP, SOIC and MSOP |
Two grades and what the A column means
The device is sold in A and B grades, both rated over the industrial temperature range, and the grades differ in offset and drift rather than in bandwidth. For a photodiode preamp the grade matters less than the bias current, because the offset can be removed by a servo or by calibration while the bias current cannot. Where the grade does matter is in a multi channel instrument that has to hold channel to channel matching across temperature without a per channel calibration step, because drift, not initial offset, is what breaks the match. Reading the ordering table before substituting one grade for the other is worth the minute it takes, since the two share a body and a footprint and nothing on the board will flag the difference.
Why an input range below ground solves a real problem
Sensors that sit at the end of a long cable often return a signal that dips a few hundred millivolts below the local ground because of return current in the shield. An amplifier whose input range stops at the negative rail clips that dip and the reading shows a flat spot at zero that looks like a sensor fault. Extending the input range below ground keeps the loop closed through the dip. This is also the reason the part appears in twelve and fourteen bit data acquisition channels where the converter's own input range starts at zero, because the buffer can sit between a bipolar sensor and a unipolar converter without a level shift stage that would add its own offset and drift.
The 350 pF load figure and stability
A 350 pF capacitive load rating is generous for a 1.8 MHz part and it comes from the output stage topology rather than from an external network. Above that value the phase margin falls and the output rings on a step, so a board that drives a long shielded cable still needs either a series resistor or a buffer stage after the amplifier. The practical rule is to keep the capacitance seen by the output below the published figure at the highest temperature the board will see, because the output impedance rises with temperature and the margin shrinks with it. Where the load is a switched capacitor converter input, the effective capacitance during the sampling instant is what counts, not the average value.
Supply range, package and sourcing
The 5 V to 30 V single supply window means the same part works on a 5 V logic board and on a 24 V industrial loop, which is why it appears across so many different assemblies. The three bodies are not interchangeable on a finished board, and the MSOP is the one that usually goes short first because it is the version used in the highest volume consumer programs. The amplifier cross reference page groups the FET input families by bias current and supply range, the ADI part second source page shows which grades are genuinely equivalent, and the obsolete part cross reference hub covers the case where the exact grade has already been dropped and a substitute has to be qualified before the next build.