Contact Us

AD8042ARZ

Brand: Analog Devices
Analog Devices AD8042ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8042ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8042ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8042ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8042ARZ: Two 160 MHz Rail-to-Rail Channels at 5.2 mA Each

The AD8042ARZ is the dual of the family that also includes the single AD8041 and the quad AD8044, specified at 160 MHz of bandwidth at a gain of plus one, 200 V per microsecond of slew rate and 39 ns of settling to 0.1 percent. Each amplifier draws 5.2 mA, the pair draws 12 mA maximum, the output swings to within 30 mV of either rail and drives 50 mA, and the input common mode extends 200 mV below ground to within 1 V of the positive rail. Into a 150 ohm load at a gain of two, differential gain error is 0.02 percent and differential phase is 0.04 degrees, gain flatness is 0.1 dB to 14 MHz, and the worst harmonic at 10 MHz is minus 64 dBc. It runs on a single 3.3 V to 12 V supply or on plus and minus 6 V.

Published values

ParameterValue
ConfigurationDual voltage feedback amplifier
Bandwidth160 MHz at a gain of plus one
Slew rate200 V per microsecond
Settling time39 ns to 0.1 percent
Quiescent current5.2 mA per amplifier, 12 mA maximum for the pair
Output swingWithin 30 mV of either rail
Output current50 mA, 0.5 V from the rails
Input range200 mV below ground, within 1 V of the positive rail
Video0.1 dB flat to 14 MHz, 0.02 percent and 0.04 degree
DistortionMinus 64 dBc worst harmonic at 10 MHz
Supply3.3 V to 12 V single, plus and minus 6 V dual
Bodies8-lead SOIC and 8-lead PDIP

The pair is 12 mA maximum, not 10.4

Two amplifiers at 5.2 mA typical are 10.4 mA, and the datasheet quotes 12 mA maximum for the package, which is the number a power budget should use because the quiescent current rises over temperature and part to part. On 5 V that is 60 mW for the pair, and 144 mW on a 12 V rail. For a battery product running at 3.3 V the figure is 40 mW, which is still large enough that a dual is not chosen for a duty cycled sensor unless the part is shut down between readings, and this family has no shutdown pin. That absence is worth knowing before a board is committed to it.

Input range versus output range on a single supply

The output reaches the rails within 30 mV while the input stops 1 V short of the positive rail, so a unity gain buffer on a 5 V single supply cannot reproduce a 4.5 V input even though its output could reach 4.97 V. This asymmetry catches boards that were moved from a plus and minus 5 V supply to a single 5 V supply without a change of bias: the bottom of the signal still works, the top clips a volt early, and the fault looks like a converter saturation rather than an amplifier limit. Biasing the signal at 1.5 V to 2 V instead of 2.5 V recovers the range on the input side at the cost of range on the output side.

Two channels for a differential converter driver

A 12 bit or 14 bit converter with a differential input needs two matched drivers, and a dual in one package is the cheapest way to get them, because the two halves share a die and their gains track. The 0.02 percent differential gain and 0.04 degree differential phase are the numbers that describe how well the halves track as the signal moves, and they are what keeps the even order distortion products low in a differential configuration. The matching is specified into a 150 ohm load at a gain of two, which is the configuration of a video or a converter driver, so the figures apply to the real circuit rather than to an open loop test.

Video and ultrasound use the same part

The video specifications and the 50 mA output are what put this part in switchers, distribution amplifiers and cameras, and the same bandwidth and settling put it in the multi-channel front end of an ultrasound machine, where dozens of channels need a low power buffer with a predictable delay. In that application the channel to channel matching matters more than the absolute bandwidth, because the beam forming assumes that each channel's delay is the same. A dual package is a small step toward that matching, and a quad package makes it cheaper still, which is why the AD8044 quad exists in the same family. The amplifier cross reference page groups the video and driver parts by bandwidth, the ADI part second source page covers the grades that are genuinely equivalent, and the obsolete part cross reference hub covers parts that are no longer catalog items.