AD8031ARZ
Product Specifications
AD8031ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8031ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8031ARZ: The Eight Lead Body, Same 80 MHz Core
The AD8031ARZ is the same single amplifier as the five lead version in an 8-lead SOIC, which changes three things and none of them is the electrical core. The core is 80 MHz at a gain of plus one, 30 V per microsecond, 125 ns to 0.1 percent, 800 uA of supply current, rail to rail input and output with the output within 20 mV of either rail and the input 200 mV beyond them, and 15 mA of output current. What the larger body adds is a lower thermal resistance, room for the feedback network and any compensation on the same side of the part, and a footprint that most assembly houses already have in their placement programs. The high grade option specifies 1.5 mV maximum offset instead of the standard grade figure.
Published values
| Parameter | Value |
|---|---|
| Bandwidth | 80 MHz at a gain of plus one |
| Slew rate | 30 V per microsecond |
| Settling time | 125 ns to 0.1 percent |
| Supply current | 800 uA per amplifier |
| Supply range | 2.7 V to 12 V, dual to plus and minus 6 V |
| Output swing | Within 20 mV of either rail at light load |
| Output current | 15 mA |
| Distortion | Minus 62 dB at 1 MHz, minus 86 dB at 100 kHz |
| Offset voltage | 1.5 mV maximum on the high grade |
| Body | 8-lead SOIC, also available in 8-lead PDIP |
| Temperature range | Minus 40 to plus 85 degrees Celsius |
Fifteen milliamps into a real load
Fifteen milliamps of output current is the point at which the 20 mV swing to the rail stops being the number that matters. Into a 1 kohm load, 15 mA would need 15 V, which the supply does not have, so the current limit only comes into play into loads below about 200 ohm on a 5 V rail. Into a 100 ohm load, 15 mA is 1.5 V, and the swing from a 2.7 V rail with a mid scale bias is then limited to about 1.35 V in each direction. This is the arithmetic that decides whether the part can drive a 50 ohm cable: it cannot, and a stage that needs to will use a part with a higher output current rather than a higher supply.
Thermal headroom in the larger body
At 800 uA the part dissipates 4 mW on 5 V and 9.6 mW on 12 V, which is small enough that the body choice is not driven by heat in normal operation. It matters when the output is driving a heavy load: 15 mA at a 2 V drop across the output stage is 30 mW, and the 8-lead SOIC spreads that over a larger lead frame than the SOT-23. For a dense board with several amplifiers in a row, this is the difference between a 10 degree and a 25 degree rise over ambient, and the offset drift with temperature follows the junction temperature rather than the ambient.
Offset grade and the calibration decision
A 1.5 mV maximum offset sounds small until it is compared with a 12 bit code of 610 uV on a 2.5 V range, where it is two and a half codes, or with a 16 bit code of 38 uV where it is 39 codes. In a single supply system the offset is also the point around which the amplifier clips, so a 5 mV offset on a 2.7 V rail with a rail to rail output wastes 5 mV of the swing at one end. The high grade is worth its price when the channel has no calibration step, and the standard grade is fine when the system calibrates at test. Both grades share the same die and the same bandwidth, so a grade change does not change the frequency response.
Where the eight lead version is the practical choice
Boards that place the feedback resistor and the decoupling capacitor within a few millimetres of the part, or that need a guard ring around a high impedance node, are easier in the 8-lead body because there is room for a ground pin between the input and the output. The PDIP version exists for through hole prototypes and for older assemblies that are still in production. When a board is being converted from through hole to surface mount, the two bodies are electrically the same part, so the conversion is a footprint change rather than a circuit change. The amplifier cross reference page groups the rail to rail parts by body and current, the ADI part second source page covers the grades that are equivalent, and the component lead time solutions page shows which bodies are available now.