AD8015ARZ-REEL7
Product Specifications
AD8015ARZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8015ARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8015ARZ-REEL7: a 155 Mbps receiver front end where the noise floor sets the optical sensitivity
The AD8015ARZ-REEL7 is a transimpedance amplifier that turns photodiode current into a differential voltage, in an 8 lead SOIC or as bare die. It has 240 MHz of bandwidth, 1.5 ns rise and fall times, a differential output that drives ECL directly, and a specified optical sensitivity of minus 36 dBm at 155.52 Mbps. It runs from a single 5 V supply at 25 mA, works over minus 40 to plus 85 C, and is built on silicon rather than the gallium arsenide process that transimpedance amplifiers in this band used to need.
The part is the analog front end of a fibre receiver, so the numbers that decide whether it fits are the bandwidth against the data rate and the input noise against the smallest optical signal the link has to recover.
What the vendor page states
| Parameter | Value |
|---|---|
| Bandwidth | 240 MHz |
| Rise and fall time | 1.5 ns |
| Input current noise | 3.0 picoamps per root hertz at 100 MHz |
| Total input noise | 26.5 nanoamps rms to 100 MHz |
| Peak input current | plus or minus 350 microamps |
| Optical sensitivity | minus 36 dBm at 155.52 Mbps |
| Output | differential, ECL compatible common mode |
| Supply | 5 V at 25 mA, PECL or minus 5.2 V ECL rail |
| Temperature range | minus 40 to plus 85 C |
| Body | 8 lead SOIC or die |
Bandwidth against bit rate
240 MHz against 155.52 Mbps is 1.54 times the bit rate, and the 1.5 ns rise time corresponds to 233 MHz on the usual 0.35 over rise time relation, so the two figures agree. That ratio is what makes the part a 155 Mbps receiver and not a 622 Mbps one: at four times the data rate the same bandwidth is a third of what the link needs, so the device cannot be stretched upward by changing the photodiode. Downward it has margin, and the vendor notes that the bandwidth supports data rates beyond 300 Mbps with a different photodiode and a following limiting amplifier.
The noise floor against the smallest signal
Three picoamps per root hertz over 100 MHz integrates to 30 nanoamps, and the vendor total of 26.5 nanoamps rms implies a noise bandwidth near 78 MHz, which is consistent with a single pole response at 240 MHz. Against the 350 microamps of peak input that is 13,208 to one, or 82.4 dB of dynamic range. At the other end, minus 36 dBm is 251 nanowatts of optical power, which with a 0.9 amp per watt responsivity is about 0.2 microamps of average photocurrent. That is 7.5 times the 26.5 nanoamps of input noise, and the ratio is the margin the sensitivity figure is built on. A photodiode with a lower responsivity, or a connector with an extra dB of loss, eats into it directly.
Power and the supply rail
Twenty five milliamps at 5 V is 125 mW, and the same current on the minus 5.2 V ECL rail is 130 mW. The output common mode is ECL compatible, so the part can drive an ECL gate or a post amplifier without a coupling network, and the differential output also serves as a single ended to differential converter for any wideband signal. On a receiver card where the supply is already 5 V, this is the whole analog front end in one package and 125 mW.
What to put on the purchase order
The reel suffix and the body are both in the order code, and the die form is a separate line that a contract assembly house will want called out separately. The two facts worth confirming in writing are the temperature range and the supply arrangement, because a part specified to 85 C in a 5 V PECL circuit is not the same order line as the die used at a different rail in an optical module.
The amplifier and converter line is indexed on the Analog and mixed-signal ICs page, and the sourcing routes for optical module builds are under RF component sourcing and obsolete part cross reference.
Request Quote — In Stock, 100% New & Original, Full Warranty