Contact Us

AD8015ARZ

Brand: Analog Devices
Analog Devices AD8015ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8015ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8015ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8015ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8015ARZ: 240 MHz Transimpedance With a Differential Output

The AD8015ARZ takes a photodiode current and returns a differential voltage, with no external transimpedance resistor in the signal path: the 10 kohm feedback is on the die and the second stage converts to a differential output whose common mode suits emitter coupled logic. Bandwidth is 240 MHz, rise and fall times are 1.5 ns, input current noise is 3.0 pA per root hertz at 100 MHz, and the peak input current rating is 350 uA. It runs from a single 5 V supply at 25 mA and comes in an 8-lead SOIC or as die. The 240 MHz bandwidth is what supports a 155 Mbps receiver, and the datasheet is explicit that data rates beyond 300 Mbps are within reach of the front end with the right photodiode.

Published values

ParameterValue
Bandwidth240 MHz
Rise and fall time1.5 ns
Transimpedance10 kohm, on chip
Input current noise3.0 pA per root hertz at 100 MHz
Peak input current350 uA
OutputDifferential, common mode compatible with ECL
SupplySingle 5 V
Supply current25 mA
Bodies8-lead SOIC and die
Data rate155 Mbps specified, beyond 300 Mbps with a suitable diode

Three picoamps per root hertz becomes a sensitivity number

Input current noise of 3.0 pA per root hertz over a 240 MHz bandwidth, with the 1.57 factor for a single pole response, integrates to about 58 nA RMS of input referred noise. Multiplied by the 10 kohm transimpedance that is roughly 0.58 mV RMS at the output, so an input current of 1 uA, which is a strong optical signal, sits about 17 times above the noise, or 25 dB of signal to noise. At 100 nA the margin falls to 5 dB and the link is at the edge of usable. This is why a receiver's sensitivity is set by the diode capacitance and the bandwidth, and why the same amplifier that is comfortable at 155 Mbps becomes marginal when the same photodiode is used at 300 Mbps with a wider bandwidth.

The feedback resistor is inside, so the diode capacitance is the variable

Because the transimpedance is on the die, the loop is compensated for a range of photodiode capacitances rather than for one value, and the datasheet shows noise against added capacitance at the input. A diode with 1.5 pF of capacitance gives a different noise and bandwidth than one with 0.5 pF, and the difference is larger than most people expect: the input capacitance adds a pole inside the loop, and the response peaks before it rings. The practical rule is to keep the diode and its bond pad small, place the part within a few millimetres of the diode, and treat the stray capacitance of the package and the board as part of the photodiode.

Differential output into an ECL receiver

The output is differential with a common mode that suits ECL, which means a comparator or a post amplifier can be driven without a coupling network, and the differential pair rejects the supply and ground noise that a single ended output would carry into a threshold. The peak input current of 350 uA is the limit that keeps the output inside its linear range: 350 uA through 10 kohm is 3.5 V of differential swing, which is close to what a 5 V single supply can support at the stated common mode. A photodiode that produces more than that on a strong signal will compress, and the receiver's overload specification has to account for it.

Where this part sits in an optical front end

In a fibre receiver the chain is a photodiode, this transimpedance stage, a post amplifier and a clock and data recovery block, and the transimpedance stage sets the noise floor for everything that follows. A silicon alternative to a gallium arsenide front end is the point of the part: it is a low cost, single supply solution for SONET, FDDI and Fibre Channel rates. Boards being repaired or re-laid in a mature product often need exactly this part rather than a modern replacement, because the post amplifier and the threshold setting were trimmed around its output common mode. For a replacement, the 8-lead SOIC pinout and the ECL common mode are the two things to confirm before anything else. The amplifier cross reference page groups the transimpedance and post amplifier parts, the how to verify a drop in replacement page lists the checks for a front end substitution, and the obsolete part cross reference hub covers parts that are no longer catalog items.