AD7914BRUZ
Product Specifications
AD7914BRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7914BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7914BRUZ: Four Channels at 1 MSPS with a Sequencer That Runs Itself
The AD7914 is the 10-bit member of a three part family that also includes the 8-bit AD7904 and the 12-bit AD7924. All three have four single ended inputs, a channel sequencer, a 1 MSPS throughput ceiling, a 16-lead TSSOP body, single supply operation from 2.7 V to 5.25 V and a separate VDRIVE pin so the serial port can talk to a 3 V or a 5 V host regardless of the analogue supply. The conversion is started by the falling edge of chip select and the input is sampled at that instant, so there is no separate convert start pin and no pipeline delay.
Conversion time is a function of the serial clock
In this family the conversion time is set by the clock on the serial port rather than by a fixed internal timer, so a host that runs the port at 20 MHz finishes a conversion sooner than a host at 10 MHz. That is the mechanism behind the power claim: the part is specified at 6 mW maximum at 1 MSPS with 3 V supplies and 13.5 mW maximum with 5 V supplies, which correspond to 2 mA and 2.7 mA. A host that runs the port slowly gets a slower conversion and lower power in the same part, without changing a component. The ceiling is 1 MSPS and the serial clock needed for it depends on the resolution, because a 10-bit result needs ten clock cycles plus the acquisition and control cycles.
Two shutdown modes and what each one is for
The family offers a full shutdown mode, entered when both power mode bits are set, and an automatic shutdown mode that puts the part down between conversions and wakes it on the next chip select edge. Full shutdown is for a system that samples occasionally and can afford the wake up time. Automatic shutdown is for a scanner that samples in bursts or at a low rate and wants the average current to follow the rate. In the automatic mode the wake up happens inside the chip select low period, so the host does not have to insert a delay, but the acquisition window is shared with the wake up and the source impedance has to be low enough to settle in what is left.
| Parameter | Value on this order code | What it decides |
|---|---|---|
| Resolution | 10 bits | 1024 codes |
| Channels | Four single ended with sequencer | A programmed sequence repeats without host writes |
| Throughput | 1 MSPS maximum | One microsecond per channel in a sequence |
| Supply | 2.7 V to 5.25 V single | 3 V and 5 V systems from one code |
| Power at 1 MSPS | 6 mW at 3 V, 13.5 mW at 5 V | 2 mA and 2.7 mA maximum |
| Shutdown | 0.5 uA maximum | Long idle periods cost nothing |
| Conversion timing | Set by the serial clock, up to 20 MHz | A slower port means a slower conversion and less power |
| Aperture | 8.2 ns delay, 1.6 ns jitter | Adequate for sampling a signal in the megahertz range |
| Interface | SPI, QSPI, MICROWIRE and DSP compatible | Direct connection to most hosts |
| Package | 16-lead TSSOP | Automotive qualified grades exist |
The sequencer is the reason to buy four channels
A consecutive run of channels is programmed once, and the converter then cycles through them on each chip select, returning the next channel in the sequence without a write from the host. On a four channel monitor that turns the host into a pure receiver: it asserts chip select, clocks out a result and does whatever it wants with the channel number. The cost is that the sequence is fixed until it is reprogrammed, so a system that has to change channel order at run time must reprogram the sequencer rather than simply address a different channel.
Where the part fits
Four channel monitoring of supplies, currents or slow sensors at rates up to a megasample per second, inside a control loop that cannot afford pipeline latency, is the target. The 10-bit resolution gives 2.44 mV per code with a 2.5 V reference, which suits monitoring rather than precision measurement; the 12-bit AD7924 in the same socket is the choice when the requirement is one bit tighter, and the 8-bit AD7904 is the cheapest member. For BOM work, the ADC and DAC cross reference page lists all three members, the BOM consolidation page covers using one family across several boards, and the ADI part second source page covers alternates.
What the serial clock decides, in clock cycles
Because the conversion is clocked out rather than timed internally, the arithmetic of a conversion is visible on the port. At the 1 MSPS ceiling one conversion has a microsecond, and at the 20 MHz clock the part is specified at, that microsecond contains twenty clock cycles, of which ten carry the ten result bits and the rest cover acquisition, control and the inter-frame gap. A host running the port at 10 MHz has half as many cycles per conversion, so the same part converts in two microseconds instead of one and dissipates less power, without any change to the circuit. A host running at 3 MHz cannot reach the ceiling at all, whatever the converter is capable of, and that is the number to check first when a board does not meet its sample rate.