AD7864ASZ-1
Product Specifications
AD7864ASZ-1
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7864ASZ-1 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7864ASZ-1: Four Channels Sampled Within 0.35 us of Each Other
The AD7864 is a four channel, simultaneously sampling, 12 bit converter with a 1.65 us conversion time, four track and hold amplifiers and a 2.5 V reference, all on a single 5 V supply. The four channels sample at the same instant, so the relative phase between them is preserved, which is the entire reason to use this part instead of a multiplexed converter with the same resolution. Single channel throughput is 500 kSPS; with all four channels converted, the read during conversion sequence gives 130 kSPS, and read after conversion depends on the processor's read cycle.
The phase information that multiplexing destroys
A multiplexed converter measures channel one, then channel two a few microseconds later. On a three phase motor the current in each phase moves during that interval, so the three readings belong to three different points on the waveform and the computed vector carries an error proportional to the sampling skew times the frequency. At 50 Hz, a 5 us skew is 0.09 degrees; at 400 Hz it is 0.7 degrees, which is a torque ripple term. Sampling all four channels within a 0.35 us aperture removes that term and makes the timing error a specification rather than a computation.
Reading the throughput numbers correctly
The 500 kSPS figure applies to converting one channel. Converting all four in sequence and reading during each conversion gives 130 kSPS, which is 32.5 kSPS per channel, because the four conversions plus their reads occupy the frame. The 1.65 us conversion and the 0.35 us acquisition are per channel, so a four channel frame at 130 kSPS is 7.7 us, of which 6.6 us is conversion. A system that needs 100 kSPS on four channels cannot use this part; one that needs four channels at 30 kSPS with exact simultaneity can.
| Parameter | Value | What it decides |
|---|---|---|
| Resolution | 12 bit | 4.88 mV per code on the 20 V span |
| Channels | Four, simultaneous | Phase between channels is preserved |
| Aperture | 0.35 us acquisition | Sampling skew inside the frame |
| Conversion time | 1.65 us per channel | Four channels in 6.6 us |
| Single channel rate | 500 kSPS | The headline figure, one channel only |
| Four channel rate | 130 kSPS read during conversion | 32.5 kSPS per channel |
| Input ranges, dash 1 | Plus and minus 10 V, plus and minus 5 V | Direct connection to industrial signals |
| Input ranges, dash 2 | 0 V to 2.5 V, 0 V to 5 V | Unipolar sensors without a level shift |
| Input ranges, dash 3 | Plus and minus 2.5 V | Lower span for a smaller signal |
| Reference | 2.5 V on chip | No external reference for a 12 bit system |
| Supply | 5 V single | One rail for analog and digital |
| Power | 90 mW typical, 20 uW standby | Standby is 4500 times lower |
| Package | 44-lead MQFP | Two square tenths of an inch of board |
Overvoltage protection on the analog inputs
The inputs tolerate overvoltage, which in an industrial cabinet is the difference between a field wiring error costing a converter or a resistor. The protection has a limit and a current, and a channel driven beyond the supply through a low impedance still needs a series resistor to keep the clamp current inside its rating. The same applies to a channel that is unpowered while the field signal is present.
Sequence selection in hardware or software
Any subset of the four channels can be converted, selected either by hardware pins or by writing a register. Converting fewer channels raises the per channel rate, so a system that only needs two of the four can run them at twice the four channel rate. The trade is that the frame timing changes with the subset, and any processor code that assumes a fixed frame has to be changed with it.
Buying a simultaneous converter
The comparison across candidates is resolution, channel count, aperture skew and the four channel rate, and the order code carries the input range option, which is not interchangeable between a plus and minus 10 V board and a 0 to 5 V board. Availability is tracked through ADC DAC cross reference, and the wider question of what a motor drive needs around its converter is set out in power management cross reference. Where a board is being reworked, the checks are in how to verify a drop in replacement.