AD7801BRUZ
Product Specifications
AD7801BRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7801BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7801BRUZ: One 8-Bit Channel, a Parallel Bus and 1.75 mA at 3.3 V
The AD7801 is a single 8-bit voltage output converter that runs from 2.7 V to 5.5 V, takes its data from a parallel microprocessor or DSP bus, and has an on chip output buffer that swings rail to rail with a typical settling time of 1.2 us. The reference is either derived from the supply or applied externally at the REFIN pin, the output can be cleared asynchronously, and power down takes the part below 1 uA at 25 degrees C. Supply current is 1.75 mA maximum at 3.3 V, which is about 5 mW at 3 V, and the package is a 20-lead SOIC or TSSOP.
11.7 mV per code on 3 V, 19.5 mV on 5 V
Eight bits on a 3 V span gives 256 codes of 11.7 mV, and on 5 V it is 19.5 mV. Those steps are coarse, and the part is honest about what that means: it is a trim, a threshold or a bias setter, not a signal source. What it offers instead is a parallel interface that writes in one bus cycle, a rail to rail buffer that needs no external amplifier, and a supply current small enough that a battery instrument can leave it powered. On a board where the host has a parallel bus and no spare serial port, that combination is still the shortest path to a controlled voltage.
The internal reference is the supply
With the internal reference selected, the output is a fraction of VDD, so any change in the rail changes the output in proportion. On a 3.3 V rail with 5 percent tolerance the full scale moves by 5 percent, which is 13 codes at 8 bits, and that is larger than the converter's own linearity error. The arrangement is correct when the load is ratiometric, such as a contrast voltage or a bridge excited from the same rail, and wrong when the output has to be an absolute value. The REFIN pin accepts an external reference for the second case, and the buffer then holds the output independent of the rail as long as the rail stays above the reference.
| Parameter | Value | What it decides |
|---|---|---|
| Resolution | 8 bits, one channel | 11.7 mV per code on 3 V, 19.5 mV on 5 V |
| Supply range | 2.7 V to 5.5 V | 3.3 V and 5 V hosts from one part |
| Interface | Parallel, microprocessor and DSP compatible | One bus cycle per update |
| Reference | Supply derived or external at a pin | Ratiometric or absolute by connection |
| Output buffer | Rail to rail, on chip | No external amplifier |
| Settling time | 1.2 us typical | Faster than the bus that writes it |
| Supply current | 1.75 mA maximum at 3.3 V | About 5 mW at 3 V |
| Power down | Below 1 uA at 25 degrees C | The off state of a portable instrument |
| Clear | Asynchronous CLR | Zero output without a bus write |
| Load drive | Buffered, defined load range | The buffer sinks and sources the load current |
| Logic levels | CMOS and TTL compatible | Interfaces to both host families |
| Package | 20-lead SOIC or TSSOP | Through hole legacy boards use the wider body |
| Update | LDAC for a delayed transfer | Load now, change later |
What the 1.2 us settling does not mean
A 1.2 us settling time suggests a waveform application, and the part can indeed produce a stepped waveform at a few tens of kilohertz. But the digital feedthrough and the glitch energy at the output are specified for a dc set point, and a waveform built from 8-bit steps of 11.7 mV carries a reconstruction error that is 11.7 mV peak, which is 1 percent of full scale. For a control voltage or a bias that is invisible; for anything that is listened to or measured it is significant. The settling time describes the amplifier, not the suitability of the part as a signal source.
Parallel interface in a serial world
Eight data lines plus a write strobe and a chip select is a lot of pins for one 8-bit value, and most modern hosts would rather use two wires. The part stays in production because it drops into boards where the bus already exists, and because a parallel write has no protocol overhead and no clock recovery question. Where a new board is being laid out, the serial equivalents in the same family do the same job with fewer pins, and the decision is made on the host's available ports rather than on any electrical difference.
Sourcing a legacy 8-bit converter
The parallel interface and the 20-lead footprint keep this part in bills of materials for boards that are still in production, so a substitute has to match the bus timing before anything else. Parts that can be compared on resolution, interface and reference arrangement are listed in ADC DAC cross reference, the check list for a same footprint replacement is in how to verify a drop in replacement, and the route when the original code ends is covered in component obsolescence management.