AD7616BSTZ
Product Specifications
AD7616BSTZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7616BSTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7616BSTZ: 1 Mohm of Input Impedance Removes the Driver Amplifier
The AD7616 is a 16 channel data acquisition system with two 16 bit successive approximation converters that sample simultaneously, a throughput of 2 by 1 MSPS, and independently selectable input ranges of plus and minus 10 V, plus and minus 5 V and plus and minus 2.5 V. Each analog input presents 1 Mohm of impedance, which does not change with the sampling frequency, and the inputs tolerate plus and minus 21 V through clamp protection. Signal to noise ratio is 90.5 dB at 1 MSPS and 92 dB at 500 kSPS with two times oversampling, and total harmonic distortion is -103 dB.
What 1 Mohm changes in a cabinet
A switched capacitor input presents an impedance that falls as the sampling rate rises, so the amplifier in front of it has to be chosen for the worst case rate and has to settle in the sampling window. A 1 Mohm resistive input does not do that, so the driver amplifier can be replaced by a resistor divider and a filter. In a 16 channel system that removes sixteen amplifiers, their supplies and their offset terms. The clamp protection at plus and minus 21 V then handles the field wiring errors that the amplifiers would otherwise have to survive.
Simultaneous pairs, not sixteen independent channels
The two converters each scan eight channels, and the sampling is simultaneous between the pair. That structure suits three phase power measurement, where two voltages or two currents have to be compared at the same instant, and it suits protective relays, where the phase between two quantities is the measurement. Sixteen channels sampled one after another would put up to 15 us between the first and the last at 1 MSPS, which at 50 Hz is 0.27 degrees and at the thirteenth harmonic is enough to change a computed phasor.
| Parameter | Value | What it decides |
|---|---|---|
| Resolution | 16 bit | 305 uV per code on the 20 V span |
| Channels | 16, in two simultaneous groups of 8 | Pairs sampled at the same instant |
| Throughput | 2 by 1 MSPS | 125 kSPS per channel across all 16 |
| Input ranges | Plus and minus 10, 5 and 2.5 V | Set per channel, not per part |
| Input impedance | 1 Mohm, independent of rate | No driver amplifier needed |
| Clamp protection | Plus and minus 21 V | Survives a field wiring error |
| Signal to noise at 1 MSPS | 90.5 dB | 14.7 effective bits |
| Signal to noise at 500 kSPS | 92 dB with 2 times oversampling | One and a half bits bought with rate |
| Total harmonic distortion | -103 dB | Below one code at 16 bits |
| Integral nonlinearity | Plus or minus 1 LSB typical | 0.99 LSB differential maximum |
| ESD on the analog inputs | 8 kV | Board level protection still required |
| Supplies | 5 V analog, 2.3 V to 3.6 V interface | Talks to a 3.3 V processor |
| Package | 80-lead LQFP | Sixteen channels in one body |
The on chip filter and the antialiasing question
The part includes a first order antialiasing filter and a selectable digital filter with oversampling. A first order analog filter rolls off at 6 dB per octave, which is not enough to remove a switching harmonic that sits just above the Nyquist frequency, so an external filter is still required where the out of band signal is large. The digital oversampling improves the noise floor and the stopband rejection inside the converter, but it cannot remove a signal that has already aliased at the input.
Sequencer and burst mode
The sequencer can be programmed with a channel list and a burst mode, so the part converts the listed channels at full rate and then idles. That is how a system keeps a fast scan for the critical channels and a slow scan for the rest, without a processor writing a channel address per conversion. A protective relay typically reads its current channels at the full rate for a cycle or two and then spends the rest of the time in the auxiliary channels.
Buying a 16 channel data acquisition part
The comparison across candidates is channels against package, input impedance against driver cost, and signal to noise at the intended rate. The order code fixes the package and the temperature grade. Availability is tracked through ADC DAC cross reference, and the wider question of a power line monitoring bill of materials is set out in power management cross reference. Where the original part is short, the options are in BOM shortage recovery.