AD7190BRUZ-REEL
Product Specifications
AD7190BRUZ-REEL
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7190BRUZ-REEL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7190BRUZ-REEL: 24-bit sigma-delta converter with a PGA, 4.8 kHz output
The AD7190BRUZ-REEL is a complete analog front end for precision measurement: a 24-bit sigma-delta converter with an on-chip low noise gain stage, two differential or four pseudo differential inputs, a channel sequencer, and output data rates from 4.7 Hz to 4.8 kHz, in the 24-lead TSSOP on tape and reel. RMS noise is 8.5 nV at 4.7 Hz with a gain of 128, offset drift is 5 nV per degree C and gain drift is 1 ppm per degree C, which is the class of stability that weigh scales and strain gauge front ends need.
Published values
| Parameter | Value |
|---|---|
| Resolution | 24 bit, up to 22.5 noise free bits at gain 1 |
| Noise free bits at 2.4 kHz | 16 at gain 128 |
| RMS noise | 8.5 nV at 4.7 Hz, gain 128 |
| Offset drift | 5 nV per degree C |
| Gain drift | 1 ppm per degree C, specified over time |
| Input channels | 2 differential or 4 pseudo differential, with sequencer |
| Gain | 1 to 128, programmable |
| Output data rate | 4.7 Hz to 4.8 kHz |
| Rejection | Simultaneous 50 Hz and 60 Hz |
| Clock | Internal 4.92 MHz, or external clock or crystal |
| Supply and current | AVDD 4.75 V to 5.25 V, DVDD 2.7 V to 5.25 V, 6 mA |
| Package and grade | 24-lead TSSOP, minus 40 C to plus 105 C |
Noise free bits are not the same as resolution
The part is a 24-bit converter that delivers up to 22.5 noise free bits at a gain of 1, and 16 noise free bits at 2.4 kHz with a gain of 128. Both numbers are honest and neither applies to every configuration. At the slow end the noise is 8.5 nV RMS, which is below the thermal noise of most sensor bridges; at the fast end the same converter gives 16 usable bits, which is still four more than a 12-bit converter at twenty times the rate. A buyer who needs 20 bits has to either accept a slower output rate or add a lower noise front end, and the datasheet's noise tables per gain and per rate are the place to check which combination actually delivers it.
Drift is what separates this part from a cheaper converter
Offset drift of 5 nV per degree C on a 2.5 V bridge signal is 0.0002 percent per degree C, which over a 60 C swing is 300 nV, or about 2.5 microstrain on a typical gauge factor. Gain drift of 1 ppm per degree C contributes 60 ppm over the same swing, which is why the reference, not the converter, usually sets the absolute gain stability. The part is specified over minus 40 C to 105 C, which is narrower than most industrial parts and is the one number that limits where it can be used. A weigh scale in a cold store at minus 30 C is inside the range on paper, but the calibration has to be done at the temperature the scale actually sees.
The sequencer and the 50/60 Hz rejection
The channel sequencer lets several inputs be enabled once and converts them in turn, so a four channel front end does not need the host to reprogram the input on every conversion. Simultaneous 50 Hz and 60 Hz rejection at the standard output rates means a reading is not corrupted by mains pickup, which is why the part appears in weigh scales, pressure transmitters and PLC analog input modules. Two digital filter options trade settling time against rejection: a sinc filter settles in one conversion period, and the zero latency option settles all conversions so a multiplexed channel change does not leave one stale result in the sequence.
Front ends that need the noise and the drift together
Weigh scales, strain gauge transducers, pressure measurement and chromatography are the vendor's own list, and they share the requirement that a small signal has to be resolved and stay resolved over temperature. The converter comparison work sits on the ADC and DAC cross reference, the medical instrumentation side is described on medical device components, and the second source position for precision converters is on ADI part second source.