AD654JRZ-REEL7
Product Specifications
AD654JRZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD654JRZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD654JRZ voltage to frequency converter: 500 kHz full scale, 2 mA of supply
The AD654 is a monolithic voltage to frequency converter with a 500 kHz full scale frequency, a 5 V to 36 V single supply range, a 2.0 mA quiescent current and an input resistance of 250 megohm. The JRZ order code is the 8-lead SOIC. It needs one RC network to set the full scale and one pull-up for the open collector output, which is why it survives in products where a microcontroller with an ADC would also fit but cannot be isolated easily.
Published values
| Parameter | Value |
|---|---|
| Full scale frequency | up to 500 kHz, set by one timing resistor and one timing capacitor |
| Transfer function | output frequency equals input voltage divided by 10 times R times C |
| Supply | 5 V to 36 V single supply, or plus and minus 5 V to plus and minus 18 V dual |
| Quiescent current | 2.0 mA |
| Input offset | 1 mV |
| Input resistance | 250 megohm |
| Dynamic range | 80 dB |
| Output stage | open collector, sinks more than 10 mA, saturation below 0.4 V |
| Load drive | up to 12 TTL loads, optocouplers or long cables |
| Package | 8-lead SOIC |
Choosing R and C from the frequency you need
The transfer function is fixed by the data sheet: frequency equals the input voltage divided by 10 R C. A 0 to 10 V input that should produce 0 to 100 kHz therefore needs R times C of 10 microseconds, which is a 10 kohm resistor with a 1 nF capacitor. Changing the resistor alone scales the span; changing the capacitor alone scales it in the other direction but also moves the ripple.
The 500 kHz ceiling is a data sheet limit, not a suggestion. A 20 V full scale input at 500 kHz needs R times C of 4 microseconds, so the timing resistor falls and the input bias current becomes a larger part of the error. Products that need both a wide input range and a high frequency usually split the job into two ranges rather than push one RC network.
Why a frequency output is still useful
A frequency can be transmitted across an isolation barrier with a pulse transformer or an optocoupler, and it can be counted by a timer input on any microcontroller. An analog voltage cannot do either without an isolated amplifier or an isolated ADC, both of which are larger and more expensive than a converter and a gate.
The 80 dB dynamic range sets the resolution: a 500 kHz full scale with a 0.1 s counting gate gives 50,000 counts, about 15 bits, while a 10 ms gate gives 5,000 counts, about 12 bits. The gate time, not the converter, is the accuracy decision in a counting system.
The output stage is open collector
The output sinks more than 10 mA with a saturation below 0.4 V, so the pull-up resistor and the supply it returns to set the logic level. That is what allows a 3.3 V microcontroller to read a converter running on a 24 V loop supply without a level shifter. Long cable runs need the pull-up at the receiving end so the current loop is closed at the far end rather than at the converter.
Sourcing notes for this family: the ADC and DAC cross reference holds the cross references, the obsolete part cross reference hub is the pre substitution check, and component lead time solutions is what we use when the part on the drawing is not on the shelf.
Two questions buyers ask
Can the AD654 run from a single 5 V supply with a 10 V input? No. With a single 5 V supply the input range has to stay inside the supply rails, so a 10 V full scale needs at least a 12 V rail or a divided input. The data sheet allows 100 mV to 10 V or more depending on the supply.
What replaces the AD654 if it becomes hard to find? The candidates are other voltage to frequency parts with the same RC transfer function, plus a small microcontroller that measures the analog input and generates a frequency in firmware. The second route changes the accuracy story, because the microcontroller reference becomes the limit rather than the converter.