AD5660CRMZ-2
Product Specifications
AD5660CRMZ-2
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD5660CRMZ-2 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD5660CRMZ-2: 16 Bits on a 5 V Span From a SOT-23 and a 2.5 V Reference
The AD5660 is the 16-bit member of the single channel nanoDAC family, with an on chip reference specified at 5 ppm per degree C, a SPI interface and an 8-lead SOT-23 package. The suffix matters: the minus 1 parts carry a 1.25 V reference and give a 2.5 V full scale span, and the minus 2 and minus 3 parts carry a 2.5 V reference and give a 5 V full scale span. This page is the minus 2 part, so the full scale is 5 V and one code is 76.3 uV. The supply range is 3 V to 5 V, the converter is monotonic by construction, power down draws 480 nA at 5 V and 200 nA at 3 V, and the power on reset state is zero scale or midscale depending on the order code.
76.3 uV per code, and a reference that drifts 33 codes
On a 5 V span a 16-bit code is 76.3 uV, which is a voltage that no bench multimeter resolves without care. The on chip reference is specified at 5 ppm per degree C, so over a 100 degree excursion the reference moves 500 ppm, which is 2.5 mV at full scale, or 33 codes. That single term is larger than the converter's own linearity error by a wide margin, and it is the reason a 16-bit DAC with an internal reference is a 12-bit to 13-bit absolute instrument unless the reference is calibrated or the measurement is ratiometric. In a ratiometric arrangement, where the same reference drives the DAC and the converter that measures the result, the drift cancels and the full resolution becomes usable.
The three power down modes
The part has three power down functions selected by the control word, which differ in what the output amplifier does while the converter is off: 1 kohm to ground, 100 kohm to ground, or high impedance. The choice is a system decision rather than a power decision. A high impedance output is what a multiplexed node needs, a 1 kohm to ground output is what a valve or an amplifier input needs so that it cannot float, and the 100 kohm state is the compromise for a node that has to bleed off slowly. All three draw the same 480 nA at 5 V.
| Parameter | Value | What it decides |
|---|---|---|
| Resolution | 16 bits, single channel | One code is 76.3 uV on the 5 V span |
| Reference | 2.5 V on chip, 5 ppm per degree C | 500 ppm over 100 degrees, 33 codes |
| Full scale | 5 V, from the gain of 2 | The minus 2 suffix, not the minus 1 |
| Monotonicity | Guaranteed by construction | No missing codes at 16 bits |
| Supply | 3 V to 5 V single | 5 V span needs a 5 V rail and 1.5 V of headroom |
| Power down | 480 nA at 5 V, 200 nA at 3 V | 4.2 mAh over a year in the off state |
| Power down modes | 1 kohm, 100 kohm, high impedance | Decides what the output node does when the DAC is off |
| Power on reset | Zero scale or midscale | Midscale drives 2.5 V before the first write |
| Interface | SPI, Schmitt triggered inputs | Direct connection to a host with a slow edge |
| Output range | Rail to rail | The buffer swings to within millivolts of both rails |
| Reference output | Available on a pin | Can bias the sensor bridge on the same board |
| Package | 8-lead SOT-23, MSOP or LFCSP | The smallest board area of the family |
| Interface rate | Up to 30 MHz clock | A 24-bit frame takes 0.8 us at that rate |
Power on reset is a safety question, not a convenience
A converter that resets to midscale drives 2.5 V into whatever it is connected to as soon as the rail is up, before the host has written a single word. On a bias network that is harmless; on a laser diode current control or a valve driver it is an event. The order code selects the reset state, and the selection has to match the fail safe direction of the actuator, not the convenience of the firmware. Where the load must be off at power up, the zero scale option is the only correct one, and the external network should still be arranged so that a floating node is safe.
The 5 V span and the rail it needs
A 5 V full scale output from a rail to rail buffer needs a supply above 5 V by the output stage's headroom, which in practice means a 5.5 V supply or a negative rail for the amplifier. Running the part from a 5 V rail and expecting the top of the span to reach 5.000 V is a common error: the top codes compress and the last few dozen codes are lost. The data sheet specification is written for the 5 V supply with the load conditions stated, so the top of the span is what the table says under those conditions, and a board that must guarantee 5 V at code 65535 has to give the part more headroom.
Buying a 16-bit set point in a SOT-23
The family spans 12, 14 and 16 bits and two reference voltages in the same footprint, so a footprint that is right for the minus 2 part will also take the minus 1 and the 12-bit members, which is what makes a platform strategy possible. The substitution question is then the reference voltage and the reset state, not the pinout. Parts that can be compared on resolution, reference and package are listed in ADC DAC cross reference, the check list for a same footprint substitute is in how to verify a drop in replacement, and consolidating a set point bill of materials is covered in one stop BOM sourcing.