Contact Us

AD5601BKSZ-500RL7

Brand: Analog Devices
Analog Devices AD5601BKSZ-500RL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD5601BKSZ-500RL7 — Analog & Mixed-Signal ICs | Superb Automation

AD5601BKSZ-500RL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD5601BKSZ-500RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

AD5601BKSZ-500RL7: an 8-bit nanoDAC in a 6-lead SC70 that runs from 100 microamps

What this order code is

AD5601BKSZ-500RL7 is the 8-bit member of the nanoDAC family from Analog Devices, a single channel buffered voltage output converter in a 6-lead SC70. The family covers 8, 10 and 12 bits in the same package and the same interface, so an upgrade along the bit count is a code change rather than a board change as long as the order code keeps the same body suffix.

The reference is derived from the supply, which is unusual and is the defining feature: the output spans 0 to the supply rail, so the full scale is exactly the rail the part runs from, and the accuracy of the output follows the accuracy of that rail. The B grade carries plus or minus 0.5 LSB of integral nonlinearity, guaranteed monotonic. A power on reset holds the output at 0 V until a valid write arrives, brownout detection is included, and three power down functions are available with software selectable output loads while powered down. The interface is a three wire serial port that runs to 30 MHz and is compatible with SPI, QSPI and MICROWIRE.

Parameters as published

ItemValue
Resolution8 bit
Supply range2.7 V to 5.5 V
Referencederived from the supply rail
Supply current75 microamps typical, 100 microamps maximum at 5 V
Power down current0.2 microamps typical at 3 V
Integral nonlinearity, B gradeplus or minus 0.5 LSB
Monotonicityguaranteed
Output bufferrail to rail, 0.5 V per microsecond typical
Interface3 wire serial, 30 MHz, SPI and QSPI compatible
Power on resetto 0 V, with brownout detection
Package6-lead SC70 and 6-lead LFCSP
Other family membersAD5611 at 10 bit, AD5621 at 12 bit

Numbers that decide the application

One count at 8 bits is 19.5 mV on a 5 V rail and 11.7 mV on 3.0 V. Those step sizes are the reason this family is used for bias and threshold setting rather than for signal generation: a 19.5 mV increment is fine for setting a comparator threshold or a amplifier bias point and far too coarse for audio or for a control loop that needs millivolt resolution.

Because the reference is the supply, a one percent error on the rail is a 2.56 count error at the top of the scale, and any ripple on the rail appears directly at the output through the buffer. A board that feeds this converter from the same rail as a switching regulator will see that regulator's ripple in the output code. The usual answer is a separate quiet rail or a small series resistor and capacitor ahead of the supply pin, and the cost of that decision is still lower than adding a reference.

The current figures are the other half of the case. One hundred microamps maximum at 5 V is 876 mAh over a year, which is not small in a coin cell product; the typical figure is 75 microamps. Power down at 0.2 microamps is 1.75 mAh over a year, so a board that updates the output occasionally and sleeps between updates spends almost nothing, and the three power down modes let the output sit at a defined state rather than floating.

Speed is not a constraint. Sixteen clock cycles at 30 MHz is 533 ns to write a code, and the output buffer slews a full 5 V span in 10 microseconds at 0.5 V per microsecond, so the settling of the buffer rather than the bus sets the update rate. Half an LSB at 5 V is 9.8 mV, which is the resolution floor the buffer has to hold.

Selection and cross reference notes

The three family members share a package and an interface and differ only in resolution, which makes the choice easy: pick the bit count the application needs and keep the body suffix. What is not interchangeable is the grade. The A versions of the 10 and 12 bit parts carry much wider nonlinearity, four and six counts respectively, so a quotation that does not name the grade can deliver a converter with eight times the error of the B part.

Because the reference is internal to the supply, this part cannot be compared directly with a converter that has a precision reference input. A 12 bit part with a 0.1 percent reference will beat this one on absolute accuracy at any bit count, and it will cost more and take more board area. The comparison that matters is against the total error the application can tolerate, not against the bit count.

Where it fits

Level setting in portable and battery powered equipment is the vendor's stated use: bias voltages, threshold trims, control voltages in space constrained instruments. The 6-lead SC70 body is 2 mm by 2.1 mm, which is why it appears on boards where nothing else fits. Medical and portable instrument builds use it for detector bias and offset trims, and industrial boards use it for setting a comparator window that has to be trimmed at test. Buyers comparing converters can start at the ADC and DAC cross reference page, and cost reduction work on an existing converter line usually starts from the component cost reduction page.

Buying notes

The code carries resolution in the family name and body in the suffix: BKSZ is the SC70, 500RL7 is the 500 piece reel. The B in the position before the body is the grade, and that letter is where the accuracy lives. Because the 8, 10 and 12 bit parts look identical in a photograph, the label is the only way to tell them apart after the reel has been opened.

Sourcing notes and next step

These parts are consumed in high volume by test and trim stations, so the questions are the grade, the reel size and the date code. We quote the exact string and confirm the grade letter before shipment. Send the codes and annual quantities through the BOM shortage recovery page and we will answer with availability and packaging.

Request Quote — In Stock, 100% New & Original, Full Warranty