AD5262BRUZ20-RL7
Product Specifications
AD5262BRUZ20-RL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD5262BRUZ20-RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD5262BRUZ20-RL7: Two 256 Position Pots on a 15 V Supply
The AD5262BRUZ20-RL7 is the dual channel member of a 15 V digital potentiometer family, with 256 positions per channel, 20 kohm terminal resistance, and independent programming for the two halves. The 15 V in the title is the part's real claim: the resistor terminals can sit at a much higher voltage than the logic supply allows, so the device can be used in a bipolar or high voltage analog loop where a 5 V digital pot would break down. The package is a TSSOP in 16 leads, the interface is a four wire SPI compatible serial input, and the wiper comes up at midscale at power on rather than at zero, which is the safer default in a gain loop.
Published values
| Parameter | Value |
|---|---|
| Channels | Two, independently programmable |
| Positions | 256 per channel |
| Terminal resistance | 20 kohm in this version, also 50 kohm and 200 kohm |
| Supply | Positive rail specified at 5 V or 15 V |
| Negative rail | 0 V to minus 5 V |
| Rail sum limit | Magnitude of the positive rail plus the negative rail, 15 V |
| Logic supply | Separate VL pin, tied to the host logic level |
| Power on state | Midscale preset |
| Interface | Four wire SPI compatible |
| Body | 16-lead TSSOP, tape and reel |
The separate logic supply is the pin people forget
The VL pin sets the digital input thresholds and must be tied to the same voltage as the logic driving the part. On a board where the host runs at 3.3 V and the pot runs from plus and minus 5 V, leaving VL at 5 V means the part reads a 3.3 V high as marginal, and the failure appears as random wiper jumps at temperature rather than as a dead part. Tying VL to the 3.3 V rail costs one trace and removes the whole class of problem. It is also the first thing to check when a pot appears to ignore commands that work on the bench.
Power on midscale and why it is the right default
A wiper that comes up at zero puts an amplifier at one extreme of its gain, which in a power stage can mean maximum output at the instant the rails come up. Midscale puts the loop near the middle of its range, so the initial condition is bounded and the firmware has time to program the real value. This matters in an audio level control, where a wiper at zero is silence and a wiper at full is a transient into the speakers, and it matters in a bias loop where zero bias is not the safe state.
Rail to rail signal swing across the resistor terminals
The resistor terminals can swing from the negative rail to the positive rail, subject to the 15 V sum limit, which is what allows the part to sit inside a plus and minus 5 V signal path or a single 15 V one. The limit is a sum rather than two independent maxima, so a board using plus and minus 7.5 V is inside the specification while a board using plus and minus 10 V is not, even though neither rail alone exceeds 15 V. Reading the limit as a sum is the difference between a working bias control and a part that fails after a few weeks.
Two channels, matched or independent
Because the two halves are independent, a stereo level control can be trimmed channel by channel, and a pair of gain stages can be set to different values from one package. What is not guaranteed is matching between the two resistor strings, so a circuit that relies on both channels having the same end to end resistance needs a calibration step. The 256 positions give about 0.4 percent of full scale per step, which is fine for a level control and too coarse for a precision gain trim, which is where the 1024 position family fits instead. The ADI part second source page lists the digital pot families by resolution, supply and memory, the pin to pin cross reference page covers direct body swaps, and the lead time page shows availability for the resistance versions.