AD1886JST
Product Specifications
AD1886JST
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD1886JST from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD1886JST: A 16-Bit AC'97 Codec Whose 1 Hz Sample Rate Step Is the Real Feature
The AD1886 is a SoundMAX AC'97 codec: a 16-bit stereo full duplex converter that carries audio over the AC-link instead of a serial audio port, with four stereo line level inputs, two mono inputs and a microphone preamplifier. The revision in hand is the AD1886A, which is the AC'97 2.2 compliant member of the family, so a board qualified against an earlier 2.1 codec has to read the revision mark on the reel before assuming register behaviour is identical. It is supplied from 3.3 V digital and 5 V analog rails and comes in a 48-lead LQFP.
The variable rate core runs from 7.04 kHz to 48 kHz in 1 Hz steps
Most codecs of this generation lock to a small set of rates derived from a 12.288 MHz master clock, and every rate is an integer division of that clock. The AD1886 instead runs its converters over a variable rate range of 7040 Hz to 48 kHz with 1 Hz resolution, which means the sample rate is a register value rather than a divider ratio. For a voice or telephony function that has to sit on an 8 kHz PCM backbone, that granularity removes the resampling stage that would otherwise be needed between the codec and the line interface. It also means the rate register has to be written before the converter is unmuted, because a rate change mid stream shifts the filter corner and the output carries a click.
Sixteen bits and the noise floor that goes with them
The data path is 16 bits, so the theoretical dynamic range over a 20 Hz to 20 kHz band is 98 dB, and the specified figure is greater than 90 dB. The 8 dB gap between the two is the analog front end, not the converter core: the input multiplexer, the programmable gain amplifier and the mixer all sit ahead of the modulator. The programmable gain amplifier covers 0 dB to 22.5 dB in 1.5 dB steps, which is fifteen settings, and the master volume covers 0 dB to minus 94.5 dB in the same 1.5 dB step, which is 63 settings. A volume control built from 1.5 dB steps is coarse enough to hear as a step on music but fine enough for speech, and the mute attenuation is specified as 80 dB below the fundamental.
| Parameter | Value | What it decides |
|---|---|---|
| Resolution | 16 bits stereo full duplex | 98 dB theoretical range over the audio band |
| Dynamic range | Greater than 90 dB | 8 dB below the 16-bit ideal, set by the analog front end |
| Sample rate range | 7040 Hz to 48 kHz | 1 Hz steps, so no resampler between codec and line |
| Master volume | 0 to minus 94.5 dB | 1.5 dB steps, 63 settings plus mute |
| Headphone volume | Plus 6 to minus 88.5 dB | A 6 dB boost above the line level scale |
| Mono output volume | 0 to minus 46.5 dB | Speakerphone path stops 48 dB above the line path |
| Programmable gain amplifier | 0 to 22.5 dB | 1.5 dB steps for microphone and line sources |
| Microphone preamp | 20 dB, switchable | Two sources selectable at the pin |
| Line level stereo inputs | Four | LINE_IN, CD, VIDEO and AUX on one mux |
| Mono inputs | Two | Speakerphone and PC beep, summed separately |
| SPDIF output | 20 bits, three symbol rates | 32 kHz, 44.1 kHz and 48 kHz, not the variable rate |
| Supplies | 3.3 V digital, 5 V analog | Two rails, sequenced by the AC-link reset |
| Package | 48-lead LQFP | 0.5 mm pitch, four sided leads |
Split supplies and what the 5 V analog rail buys
The digital core runs at 3.3 V and the analog section at 5 V. The split is not decoration: a 5 V analog rail gives the input multiplexer and the headphone amplifier the headroom to pass a 1 V rms line signal with the 6 dB boost applied, which a single 3.3 V rail cannot do without clipping. The cost is a second regulator and a sequencing question, because the analog rail coming up after the digital one leaves the AC-link alive while the converters are still unpowered. The reset pin and the AC-link warm reset both have to be held until the 5 V rail is in tolerance.
Jack sense and the automatic output switch
Two jack sense pins let the codec report whether headphones are plugged in and switch the output path without host intervention. In a fixed installation the same function is done in software, and the pin is simply strapped. Where the board is a carrier for an existing single board computer, the jack sense state is usually what the operating system driver polls to decide whether the speaker channel or the headphone channel is active, so the strap has to match the driver's expectation rather than the wiring note.
Where an AC'97 codec sits in a 2026 bill of materials
AC'97 has been superseded by HDA and by simple I2S codecs, and a large part of this family is either obsolete or flagged by the vendor as not recommended for new builds. That does not make the parts unusable, because industrial carriers, medical carts and instrumentation that were qualified years ago still need them, and requalifying an audio path is a longer job than buying the original codec. The practical question is whether the exact order code with the correct package and revision is available, and what the second source looks like. Status and replacement options for a discontinued audio part are set out in obsolete part cross reference hub, and the comparison a substitute has to pass is listed in pin to pin cross reference. Where the original code has a lead time that does not fit the build, the routes out are in component lead time solutions.