Contact Us

AD1580BRTZ

Brand: Analog Devices
Analog Devices AD1580BRTZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD1580BRTZ — Analog & Mixed-Signal ICs | Superb Automation

AD1580BRTZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD1580BRTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD1580BRTZ: The 1 mV Window Grade of the 1.2 V Shunt Reference

The AD1580BRTZ is the B grade of the 1.2 V shunt reference, and the B column is what a precision instrument pays for. Initial output is 1.224 V to 1.226 V, a window of 1 mV against the 20 mV of the A grade, and the temperature drift is 50 ppm per degree Celsius maximum against 100. Everything else matches: 50 uA minimum operating current, 0.5 ohm dynamic output impedance, 2.5 mV typical output change from 50 uA to 1 mA, 5 microsecond turn on to 0.1 percent, and stability with any capacitive load. The body is the SOT-23, with an SC70 alternative for boards that are short of space.

Published values

ParameterValue
Output voltage, B grade1.224 V to 1.226 V
Temperature drift, B grade50 ppm per degree Celsius maximum
Minimum operating current50 uA
Dynamic output impedance0.5 ohm at 1 mA and 120 Hz
Output change with current2.5 mV typical from 50 uA to 1 mA
Output noise0.4 uV to 0.5 uV rms from 10 Hz to 10 kHz
Turn on settling5 microseconds to 0.1 percent
Hysteresis80 uV typical after a temperature excursion
BodiesSOT-23 and SC70

What a 1 mV window removes from the calibration

In an instrument with a 12 bit converter and a 1.2 V reference, one LSB is about 293 uV, so the 1 mV window of the B grade is roughly three counts of full scale error. That is small enough to be removed by a single point calibration at the factory, and it is small enough that a channel to channel spread across a batch stays inside the measurement tolerance without per board trimming. With the A grade the 20 mV window is about 68 counts, which forces either a trim per board or a wider specification. The cost difference between grades is almost always smaller than the cost of the trim step, which is the argument for starting from the B grade in a precision product.

Drift, hysteresis and the second power cycle

Initial accuracy is measured once, but a reference in an instrument is read after every power cycle and at every ambient temperature. The 50 ppm per degree figure over a 100 degree span is 0.5 percent, which is larger than the initial window and therefore the term that dominates the error budget in an uncooled enclosure. Output hysteresis of 80 uV typical describes the shift that remains after a temperature excursion, and it is the reason a reference that reads correctly on the bench can read differently in a unit that has been through a burn in cycle. Both figures are published for the B grade and neither is removable by calibration done at a single temperature.

The series resistor budget at low current

At 50 uA minimum and a 1.2 V output, a 3.3 V rail leaves 2.1 V across the series resistor, so a 20 kohm resistor delivers about 105 uA, which covers the reference plus a light load. A 5 V rail with the same resistor delivers 190 uA and the extra current is dissipated in the reference, which raises the die temperature slightly and shows up as drift in a sealed enclosure. Choosing the resistor against the highest supply voltage rather than the nominal is what keeps the reference inside its current window across the production spread of the power supply.

Grade substitution and the paperwork

Substituting the A grade into a B grade position is electrically safe and cheaper, but it changes the accuracy of every unit built with it, and in a regulated instrument that is a specification change rather than a purchasing decision. The reverse substitution is safe on accuracy and only affects cost. Where the B grade is short, the honest options are a different reference family with the same output voltage, which requires a resistor and noise recheck, or waiting for the grade. The ADI part second source page lists the grades that are genuinely interchangeable, the pin to pin cross reference page covers the bodies that swap without a board change, and the component lead time page shows availability for both grades on the same screen.