HX130640F5
Product Specifications
HX130640F5
Hisiwell — Amplifiers & Comparators
Product Overview
The HX130640F5 from Hisiwell is a precision amplifier / comparator delivering high gain, wide bandwidth, and low distortion for signal conditioning. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High gain-bandwidth product for wideband signal amplification
- Low input offset voltage and drift for precision DC applications
- EMI-hardened design for robust operation in noisy environments
- Rail-to-rail input/output for maximum dynamic range
- Low quiescent current for power-sensitive designs
- Unity-gain stable with capacitive load drive capability
Key Specifications
| Channels | — |
| GBWP | MHz |
| Slew Rate | V/µs |
| Vos | µV |
| Iq per Channel | µA |
| Input Type | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
HX130640F5: 16 dB from DC to 30 GHz, and the 1.56 W behind it
The HX130640F5 is a GaAs MMIC distributed amplifier in a 5 x 5 x 1.2 mm QFN, covering DC to 30 GHz with 16 dB of small signal gain, 4 dB noise figure and 23 dBm at the 1 dB compression point. It runs from 8 V at 220 mA and needs a negative gate. The device page prints 24 dBm for the same part number where the family table prints 23.
What the vendor publishes
| Parameter | Value |
|---|---|
| Frequency range | DC to 30 GHz |
| Small signal gain | 16 dB |
| Gain flatness | plus or minus 2 dB |
| Noise figure | 4 dB |
| Output P-1dB | 23 dBm in the table, 24 dBm on the device page |
| Supply | 8 V, 220 mA, negative gate |
| Input VSWR | 1.6 to 1 |
| Output VSWR | 1.4 to 1 |
| Package | QFN 5 x 5 x 1.2 mm |
Two hundred milliwatts from 1.76 W of DC
23 dBm is 199.5 mW and the drive at compression is 7 dBm, 5 mW. The DC input is 1.76 W, so 1.56 W leaves as heat, 88.7 percent of the DC. The conversion is 11.4 percent and at 24 dBm it is 14.3 percent. This is not a power amplifier and should not be read as one: it is a linear gain block with a wide band, and the current column is what a wideband distributed stage costs.
1.56 W on a 25 mm2 footprint is 62.4 mW per mm2, and against the 1.2 mm body height it is 52 mW per mm3. That is a board build question rather than a heatsink question: a via field under the pad into a ground plane on layer two is enough, provided the plane is not cut by the RF launch.
The package against the die, to a hundredth of a dB
The die version, HX130640, publishes 1.5 to 1 at the input and 1.3 to 1 at the output. The package is 1.6 and 1.4. In loss terms the input goes from 0.177 to 0.238 dB and the output from 0.075 to 0.122 dB, so the package adds 0.060 dB and 0.048 dB. Those are small enough that the choice between die and package is made on assembly cost and on the 30 GHz launch, not on the match.
At 30 GHz a 0.1 dB difference is within the tolerance of the connector and the board material, so this is one of the few places in the family where the packaged part is the obvious buy. A wire bond at 30 GHz is an inductance the buyer has to characterise; the QFN footprint is a known quantity.
Four dB of noise figure as a temperature
4 dB is 438 K of noise temperature. Behind a 16 dB gain stage that is 40 times in linear terms, so the contribution of the next stage is divided by 40 before it reaches the input. A 6 dB second stage adds 0.16 dB to the system, and a 10 dB second stage adds 0.47 dB. That is why a 16 dB block with a 4 dB noise figure is a sensible first stage for a wideband receiver, and why the same 4 dB figure on a 10 dB gain block would not be.
The DC to 30 GHz span is the other half of the argument. One part covers a 30 GHz instrument front end, a 20 GHz scope channel and a 28 GHz radio, so a buyer stocking one amplifier covers three product lines. The price is 16 dB plus or minus 2 dB, which is 14 to 18 dB across the band, and an instrument that expects flat gain has to calibrate it out.
Two questions buyers ask
Is DC to 30 GHz really DC coupled? The row says DC, which means the amplifier passes a DC level from input to output within its bias limits. In a receiver that is a hazard: any offset at the input appears at the output and can saturate the next stage. Block it with a capacitor when the signal does not need to reach DC, and check the input bias current before connecting a source that cannot sink it.
Why 8 V and 220 mA for a 0.2 W part? Because a distributed amplifier trades current for bandwidth. The same family has a 60 mA member at 14 dBm for 22 GHz of band. If the application needs 23 dBm, this row is the price; if it needs 14 dBm, the lower current part does the job with a third of the heat.
SUPERB quotes the HX130640F5 against the table figure of 23 dBm and confirms the 24 dBm device page number before an order. For a swap from a discontinued wideband part, obsolete RF part replacement lists what has to agree first. The bias and decoupling parts sit under RF component sourcing, and stock is quoted from the amplifiers and comparators index.
HX130640F5: a pad in front of a preamp is not recoverable
This is the packaged 30 GHz wideband amplifier, and the place it earns its 220 mA is inside an instrument, in front of a detector or a mixer, after an input attenuator. The usual question about that arrangement is whether the amplifier's 16 dB of gain can make up for the attenuator's loss. It cannot, and the reason is worth setting out because the same arithmetic governs every receiver front end built this way.
Loss before gain stays in the noise figure
A receiver consisting of a 10 dB attenuator, this amplifier at 4 dB noise figure and 16 dB gain, and a following stage has a noise figure of 14 dB, not 4 dB. In the Friis formula the attenuator's factor of 10 comes first and the amplifier's own 2.51 is divided by the attenuator's gain of 0.1, so the total is 25.1, which is 14 dB. The amplifier adds its 16 dB to the signal and to the noise equally, which preserves the ratio the attenuator already set.
| Arrangement | Noise figure | Comment |
|---|---|---|
| amplifier first, then 10 dB pad | 4.0 dB | the pad is after the gain |
| 10 dB pad, then amplifier | 14.0 dB | the loss is at the input |
| 20 dB pad, then amplifier | 24.0 dB | the pad sets the floor |
| no pad, amplifier only | 4.0 dB | and no protection |
Where the 16 dB actually helps
It helps after the loss, by lifting the signal above the noise floor of the next stage. If the following mixer or detector has a 15 dB noise figure, then 16 dB of gain in front of it divides its contribution by 39.8 and the system figure stays at the 14 dB the pad set rather than rising to 21 dB. That is the job: not to undo the pad, but to stop the rest of the chain from adding to it.
1.56 W inside a 5 by 5 package
The DC input is 1.76 W and 1.56 W of it is heat, which is 88.7 percent of the DC and 62.4 mW per square millimetre of footprint. In a bench instrument with a fan that is a small problem; in a sealed enclosure with no airflow it is the dominant heat source on the board. The via field under the pad is the thermal path, and it is also the RF ground, so the two have to be planned together rather than one after the other.
Two questions buyers ask
Is 24 dBm or 23 dBm the output? The family table prints 23 dBm and the device page prints 24. The difference is 0.2 W against 0.25 W, and at 11 percent efficiency either way it is a linear gain block, not a power stage. Ask which measurement the number came from if it matters.
Does the negative gate need a separate supply? Yes, the supply is 8 V with a negative gate, so a bias board inside the instrument has to make both and sequence them. A part with a single positive rail would be simpler; this family trades that simplicity for bandwidth. Parts and their published rows are on RF component sourcing, the low noise selection route is on LNA selection guide, and the obsolete part route is on obsolete RF part replacement.
Request Quote — In Stock, 100% New & Original, Full Warranty