Contact Us

HX130640

Brand: Hisiwell
Hisiwell HX130640 is a amplifiers & comparators component designed for Signal Conditioning & Filtering and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HX130640 — Amplifiers & Comparators | Superb Automation

HX130640

Hisiwell — Amplifiers & Comparators

Product Overview

The HX130640 from Hisiwell is a precision amplifier / comparator delivering high gain, wide bandwidth, and low distortion for signal conditioning. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High gain-bandwidth product for wideband signal amplification
  • Low input offset voltage and drift for precision DC applications
  • EMI-hardened design for robust operation in noisy environments
  • Rail-to-rail input/output for maximum dynamic range
  • Low quiescent current for power-sensitive designs
  • Unity-gain stable with capacitive load drive capability

Key Specifications

Channels—
GBWPMHz
Slew RateV/µs
VosµV
Iq per ChannelµA
Input Type—
Supply VoltageV
Operating Temp°C
Package—

Applications

Signal Conditioning & Filtering Current Sensing & Monitoring Data Acquisition Systems Audio & Video Processing Sensor Interface Amplifiers Industrial Control Loops

HX130640: DC to 30 GHz at 23 dBm, the most power in the wideband family

The HX130640 covers DC to 30 GHz with 16 dB of gain, plus or minus 2 dB of flatness, 23 dBm at the 1 dB compression point, 4 dB noise figure, and 8 V at 220 mA with a negative gate. It is the highest output part in this wideband series by a clear margin: 23 dBm is 199.5 mW, 8 dB more than the 15 dBm parts that make up most of the family. That extra power costs current, flatness and heat, and each of the three has a consequence on the board.

Published values

ParameterValue
Frequency rangeDC to 30 GHz
Small signal gain16 dB, flatness plus or minus 2 dB
Noise figure4 dB
Output P-1dB23 dBm
Input VSWR1.5:1
Output VSWR1.3:1
Supply8 V at 220 mA, negative gate required
FormBare die

199.5 mW and the drive that goes with it

With 16 dB of gain and 23 dBm at compression, the input at compression is 7 dBm. That is a high drive point for a wideband part, and it is the reason this device is usually found at the output of a chain rather than the input: the stages in front have to deliver 7 dBm and stay linear doing it, which means they need their own headroom. The output match helps here, 1.3:1 is 17.69 dB of return loss and 0.075 dB of mismatch loss into a 50 ohm load.

Plus or minus 2 dB is 4 dB end to end

The flatness figure is the loosest in the family, and over DC to 30 GHz it means the output moves 4 dB from one end of the band to the other, which is 151 percent in power. A part with this much level variation cannot be the only stage defining the level: either the system tolerates 4 dB of amplitude ripple, or an equaliser, a pad with a frequency slope or a level control loop absorbs it. Buyers who compare this part with a 15 dBm device on gain alone miss that the 15 dBm parts hold plus or minus 1 dB.

1.56 W of heat in a die

8 V at 220 mA is 1.760 W in, and at 23 dBm the RF output is 199.5 mW, so 11.3 percent is converted and 1.56 W stays in the die. This is the largest heat load in the family apart from the 26 to 38 GHz driver, and it is a bare die: the attach, the spreader and the spreader's mounting all sit in the thermal path. At 100 C/W the junction would rise 156 C above the base, at 50 C/W 78 C, so a spreader of a few C/W is not a luxury on this part, it is the difference between working and not. Expect to measure the case temperature on the first article rather than trusting a calculation.

The negative gate, and DC coupling

The row states a negative gate, so the sequence is gate first, drain second, and the reverse on power down. The band starts at DC, which means the part passes baseband and any DC offset at the input appears at the output amplified by 16 dB, and the following stage sees it. In a chain with a converter, either block the DC or make sure the offset is inside the next stage's range.

Two questions buyers ask

Can it drive a mixer or an antenna directly? It can drive a mixer at 23 dBm, which is a normal level for a double balanced mixer's local oscillator or an RF port. For an antenna, the 23 dBm is the last stage, not a power amplifier, and the return loss of the antenna has to be inside what the 1.3:1 output match assumes.

Is there a lower current version with the same output? The table shows only one row at 220 mA. The 15 dBm parts are far cheaper on current but 8 dB lower in power. If the 23 dBm is needed only at the bottom of the band, a band split with a smaller device above 20 GHz is usually the cheaper arrangement.

SUPERB supplies the HX130640 as bare die with the bias sequencing confirmed per order and can quote the 15 dBm family members alongside for a band split comparison. Amplifier cross reference lists the power and match terms to check before substituting a 23 dBm stage, BOM shortage recovery covers allocation, and the range sits under amplifiers and comparators.

HX130640: at 30 GHz a bond wire is a mismatch, not a connection

This is the die version of the 30 GHz wideband amplifier, and a die at 30 GHz is a different assembly problem from a die at 5 GHz. The 23 dBm output, 16 dB of gain and 1.56 W of heat are unchanged; what changes is that every discontinuity between the die pad and the board is now a significant fraction of a wavelength. At 30 GHz a wavelength is 10 mm in air and 5.35 mm in a substrate with a dielectric constant of 3.5, so a 0.5 mm bond wire is a tenth of a wavelength and its inductance is comparable with 50 ohm.

A 0.3 nH wire is 56 ohm at 30 GHz

A 0.3 nH bond wire reads 56.5 ohm at 30 GHz, 0.5 nH reads 94.2 ohm and 1 nH reads 188.5 ohm. Against a 50 ohm system, a single round wire is therefore a series reactance larger than the system impedance, and it will not match no matter what the input network does at the die. The vendor's own reference assembly solves this with ribbon or with multiple parallel wires, and the customer assembly has to copy that rather than approximate it.

ConnectionInductanceReactance at 30 GHzAgainst 50 ohm
single round wire, short0.3 nH56.5 ohmmore than the system impedance
single round wire, longer loop0.5 nH94.2 ohmunusable at the band top
two parallel wires0.25 nH47.1 ohmmarginal
ribbon, short and wide0.1 nH18.8 ohmthe practical answer

Ribbon, not round wire

A ribbon has the same cross section as a wire but a much lower inductance per unit length because its width is large compared with its thickness, and it can be bonded at both ends to keep the loop short. On a 30 GHz die it is not a refinement, it is what makes the connection a connection. Where ribbon is not available, two or three parallel wires with the shortest possible loop are the fallback, and the assembly drawing has to state the loop height as a tolerance rather than a note.

The ground is as important as the signal

The source connections are the RF ground and the thermal path at the same time. At 30 GHz the inductance of a source wire is a degeneration that no matching network can remove, so the source has to go straight down through vias or through a conductive attach to a ground that is continuous under the die. A die mounted on a carrier with a slot under it, or on an epoxy layer with voids, has a source impedance that varies from unit to unit and a gain that follows it.

Two questions buyers ask

Can this run in a QFN? The packaged sibling exists with the same 23 dBm and 16 dB, and it is the right answer for a board that cannot bond. What the package costs is a fraction of a decibel of gain, which at 30 GHz is the cheapest part of the budget.

What about the 1.56 W of heat in a die? It has to leave a die a couple of millimetres across, so the attach and the carrier are the heatsink, and a die at this frequency needs a metal carrier rather than a laminate. Amplifier options and their published rows are on RF component sourcing, the comparison route between packaged and die parts is on pin to pin cross reference, and the amplifier comparison route is on amplifier cross reference.

Request Quote — In Stock, 100% New & Original, Full Warranty