Contact Us

TJA1050T/CM,118

Brand: NXP Semiconductors
NXP Semiconductors TJA1050T/CM,118 is a mcu & embedded component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TJA1050T/CM,118 — MCU & Embedded Processors | Superb Automation

TJA1050T/CM,118

NXP Semiconductors — MCU & Embedded Processors

Product Overview

The TJA1050T/CM,118 from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

TJA1050T/CM,118: SO8 CAN transceiver with silent mode and no standby

TJA1050T/CM,118 is a third generation Philips high speed CAN transceiver with a silent mode but no standby mode in the TJA1050 high speed CAN transceiver line, described by 2003 Oct 22 product specification. It is the interface between a CAN controller and the two wire bus at up to 1 Mbaud, and it was the part that replaced the PCA82C250 and PCA82C251 with far lower emission. What it does not have is a standby mode, which is the single fact that decides whether it can be used in a node that is powered down with the bus still live.

Order code and package

Order codeTJA1050T/CM,118
Variant function on pin 5S input selects normal or silent mode; there is no VIO pin
PackageSO8, 3.9 mm body width, 8 pins
ProtocolISO 11898 (the original standard, not the 2016 revision)
Maximum data rate60 kbaud to 1 Mbaud classical CAN
Supply voltage on VCC4.75 to 5.25 V
Logic supply on VIOnot present
Temperature rangeminus 40 to plus 150 C virtual junction
QualificationAEC-Q100
Datasheet2003 Oct 22 product specification

Electrical parameters that decide the application

Bus fault voltageminus 27 to plus 40 V on CANH and CANL with no time limit
Supply currentNo standby mode at all; the S pin only disables the transmitter while the receiver stays live
Electrostatic dischargebus pins carry the automotive transient protection of the period; the human body model figures sit in the same table as the DC ratings
Thermal resistance145 K/W junction to ambient in the SO8 body, 50 K/W junction to solder point
Wake and diagnostic pinsS pin selects normal or silent mode, no standby, no wake-up and no SPLIT output
Bus pinsCANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one
Logic levelsinputs compatible with 3.3 V and 5 V devices per the feature list
Behaviour with the supply offthe transceiver disengages from the bus so an unpowered node does not load the network
ProtectionTXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family
Ordering stringthe suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order

Points to check before this part goes on a BOM

There is no standby mode. The S pin disables the transmitter and leaves the receiver running, so the node can listen without disturbing the bus, but the transceiver still draws its normal supply current. A board that needs a microamp class sleep state cannot get there with this part, and that is the usual reason a board moves to the TJA1042 or the TJA1051.

The document is dated 2003 and names ISO 11898 without a revision, so the loop delay symmetry that CAN FD needs is not specified. The part runs classical CAN at 60 kbaud to 1 Mbaud, and the whole timing table belongs to that range.

The delay from TXD to an active bus is 25 to 110 ns with the S pin low. That 85 ns spread is what a bit timing calculation has to absorb on top of the controller delay, and at 1 Mbaud it is 8.5 percent of a bit.

Bus pins stand minus 27 to plus 40 V with no time limit, the same window as the TJA1040 and narrower than the 58 V of the third generation parts. On a 24 V network the margin at the bottom is three volts, so a short to a 24 V rail with the supply off is outside the rating.

An unpowered node does not disturb the bus, which is stated as a feature and is what allows a partially powered network at all. That behaviour is passive and is not the same as a standby mode: the part is simply high ohmic with no supply, so nothing wakes it up.

The S pin has an internal pull-down, so a board that leaves it open runs in normal mode. That is convenient on a prototype and dangerous on a product, because a lifted pin or a cold joint silently changes the mode rather than failing, and the only visible symptom is bus emission.

At least 110 nodes can be connected per the feature list, which is the ISO 11898 load figure for a 60 ohm terminated bus and not a statement about the number of ECUs a vehicle network can carry.

Where this order code fits

It is the default part on older 500 kbit/s boards and on cost driven nodes that never sleep, and it stays in demand for repair of equipment built before the third generation parts arrived. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can TJA1050T be put into a low power state by the microcontroller? No. The S pin only selects silent mode, where the transmitter is off and the receiver stays on, and the supply current stays in the normal range. There is no standby or sleep mode in this part.

Is it a drop in replacement for the PCA82C250? The pinout matches and the part was introduced as its successor, but the emission and the unpowered behaviour differ. Boards that replaced the older part still have to check the 3.3 V compatible input levels and the S pin pull-down.

What happens if the S pin is left floating? The internal pull-down puts the part in normal mode, so it transmits. The failure is silent, which is why the pin should be driven or strapped rather than left open.

SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.