Contact Us

STM32L073RZT6

Brand: ST
STM32L073RZT6 is a ARM Cortex-M microcontroller from STMicroelectronics, designed for drone electronics, embedded control systems, and industrial IoT applications. Superb Automation supplies genuine STM32L073RZT6 with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

STM32L073RZT6 — ARM Cortex-M0+ Microcontroller by STMicroelectronics

The STM32L073RZT6 is an STMicroelectronics ARM Cortex-M0+ MCU in LQFP-64_10x10x05P for Embedded control and general-purpose MCU applications. Supplied by SUPERB Automation.

Part Number Decoded — Field by Field

FieldValueMeaning
STM32L073RZT6Full Part NumberSTMicroelectronics ARM Cortex-M0+ Microcontroller
STM32Product FamilySTMicroelectronics 32-bit ARM-based MCU
L0SeriesARM Cortex-M0+ based MCU — L0 series

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberSTM32L073RZT6
CoreARM Cortex-M0+
PackageLQFP-64_10x10x05P
Temperature Range−40°C to +85°C
Supply Voltage1.8V–3.6V

Product Overview

The STM32L073RZT6 is an STMicroelectronics ARM Cortex-M0+ microcontroller in LQFP-64_10x10x05P package. Part of ST's extensive STM32 portfolio, it delivers a high-performance processing platform with integrated Flash, SRAM, and a rich set of communication peripherals for Embedded control and general-purpose MCU applications. Supplied by SUPERB Automation with full traceability and competitive lead times.

Key Features & Benefits

ARM Cortex-M0+ Core — Efficient Processing for Embedded Control

The ARM Cortex-M0+ core provides deterministic real-time performance with hardware multiply/divide and optional FPU, executing control loops, communication stacks, and sensor fusion algorithms efficiently in resource-constrained embedded environments.

Rich Peripheral Set — GPIO, Timers, ADC, Communication Interfaces

Features a comprehensive set of on-chip peripherals including multi-channel DMA, 12/16-bit ADCs, advanced PWM timers for motor control, and multiple USART/SPI/I²C interfaces for sensor and communication module connectivity.

ST Ecosystem — CubeMX, HAL, LL, Middleware

Fully supported by ST's STM32Cube ecosystem including CubeMX graphical configuration, HAL/LL driver libraries, FreeRTOS integration, and extensive middleware stacks (USB, TCP/IP, FATFS, graphics) — accelerating firmware development and reducing time-to-market.

Target Applications

Embedded Control & IoT Systems

Functions as the main processing unit in embedded control systems, IoT endpoints, sensor hubs, motor controllers, and human-machine interfaces — leveraging the Cortex-M architecture for efficient, low-power operation.

Industrial Automation & Motor Control

Powers industrial motor drives, PLCs, sensor transmitters, and factory automation equipment — taking advantage of advanced PWM timers, high-speed ADCs, and CAN/RS-485 communication for distributed control architectures.

Consumer & Portable Electronics

Integrates into consumer devices, wearables, smart home products, and portable instruments — benefiting from the STM32 family's low-power modes, small packages, and extensive third-party firmware ecosystem.

Frequently Asked Questions

Is the STM32L073RZT6 supported by STM32CubeIDE?

Yes, the STM32L073RZT6 is fully supported in STM32CubeIDE with graphical pinout configuration, clock tree setup, and automatic peripheral initialization code generation — enabling rapid prototyping and production firmware development.

What firmware/RTOS options are available?

The STM32 family is supported by FreeRTOS, Zephyr, NuttX, ChibiOS, and bare-metal HAL programming. For drone applications, Betaflight, iNav, ArduPilot, and PX4 all have STM32 HAL targets.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype tray to full production volumes.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics STM32L073RZT6 MCUs with full traceability and batch-level QA documentation. Whether you need a single tray for prototype builds or pallet-level volumes for production, we source through verified channels with competitive lead times. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.

STM32L073RZT6: 192 Kbytes of flash and an LCD driver in 64 pins

The string decodes in six places, and every one of them changes what the reel contains. L is the low power product type, 073 is the subfamily that carries USB and the segment LCD driver, R is 64 pins, Z is 192 Kbytes of flash, T is the LQFP body, and 6 is the industrial range of minus 40 to plus 85 degrees C. Any other last digit is a different temperature grade on the same die, which is the first thing to confirm when a quote arrives against a part number that came from a shortage list.

Under that code sits an Arm Cortex-M0+ at up to 32 MHz, 20 Kbytes of RAM, 6 Kbytes of data EEPROM with ECC and a 12-bit converter that reaches 1.14 Msamples per second. The combination of a segment driver, an EEPROM array and a 1.65 V floor is what makes this part appear on utility meters, on thermostats and on battery instruments rather than on general control boards. The figures below are read from DS10685 Rev 7.

The order code, character by character

Product typeL, low power
Subfamily073, USB plus segment LCD
Pin countR, 64 pins
Flash densityZ, 192 Kbytes in two banks
PackageT, LQFP 10 mm by 10 mm
Temperature6, minus 40 to plus 85 degrees C
Supply with plain code1.8 V to 3.6 V, brownout reset enabled
Supply with D option1.65 V to 3.6 V, brownout reset disabled
CoreCortex-M0+ at up to 32 MHz, 0.95 DMIPS per MHz
RAM20 Kbytes
Data EEPROM6 Kbytes with ECC, 20 byte backup register
ADC12 bit, 1.14 Msamples per second, up to 16 channels
AnalogTwo 12-bit DAC channels, two comparators
LCD driverUp to 4 by 52 or 8 by 48 segments, step-up converter on board
I/OUp to 84 fast lines, 78 of them 5 V tolerant

Two flash banks on a 192 Kbyte part

The 192 Kbyte member is the only density in this subfamily with two banks and read-while-write. New code goes into the idle bank while the application keeps running from the other, so a mains dip during a field update leaves the product on a complete image rather than on a half erased page. On a meter that is read remotely once a month, that is the difference between an update that can be pushed at any time and one that needs a site visit.

The EEPROM array is the second half of the memory story. Six Kbytes of data EEPROM with ECC means the calibration constants, the tariff table and the accumulated counters do not share a page with program code, so an update of the firmware cannot disturb them and a write cycle does not block instruction fetch. Endurance and retention for that array are quoted separately from the flash in the document, and they are the numbers to check against the write frequency of the product rather than against the flash table.

Where the density is more than the application needs, the 64 Kbyte and 128 Kbyte members of the same subfamily share the pinout, and the MCU cross reference page records which of them keep the same body so that a later change of density does not become a board change.

What the segment driver covers in a real product

A four by 52 arrangement drives 208 segments, which is a three-line display with icons, units and a battery symbol, and the eight by 48 arrangement trades two backplanes for 384 segments when the product needs a longer menu. The step-up converter for the LCD bias is on the die, so the display works from the same 3.3 V rail as the logic, and the contrast can be trimmed in firmware rather than with a potentiometer. Blinking is generated in hardware, which keeps the refresh out of the main loop.

Bias trimming without a potentiometer is worth more than it sounds. A segment display behind a tinted window loses contrast as the temperature moves, and a fixed divider gives either a washed out display in a cold room or a dark one in a warm one. Because the bias is generated on the die and the contrast register is writable, the product can hold the contrast steady over the rated range with a lookup table in firmware, and a service call for an unreadable display leaves the field return list.

The analog set matches that kind of product. A 1.14 Msample converter covers a current transformer, a battery divider and a thermistor without an external multiplexer, and the two comparators work down to 1.65 V on the D option, which is what allows a wake-on-threshold from a nearly flat cell. The two DAC channels are useful for a 4 mA to 20 mA output or for a bias that has to be trimmed at test. The ADC and DAC cross reference page lists the families we compare when the channel count or the resolution has to go up.

Current budget at 3.3 V

The run figure is 93 microamps per megahertz, so 32 MHz costs about 3 mA before any peripheral is clocked. Stop mode is 0.43 microamps with 16 wakeup lines, and stop with the RTC and 20 Kbytes of RAM retained is 0.86 microamps, which is the mode a meter spends most of its life in. Standby is 0.29 microamps with three wakeup pins, and the wake from flash takes 5 microseconds.

That last number decides the software shape. A product that wakes every second to count a pulse cannot afford a 5 microsecond start plus oscillator settling if the pulse itself is 200 microseconds wide, so the counter is usually a hardware timer running from the low speed clock and the core only wakes to move the total into EEPROM. Choosing the retention window and the wake source is a power budget exercise, not a firmware preference, and it is worth doing before the enclosure is frozen.

The EEPROM array has its own wear story. A meter that writes a total once an hour accumulates 8760 cycles a year, and over fifteen years that is 131 thousand cycles on the same row, which is inside the endurance of the array but not inside it by a wide margin. The usual software answer is to keep a shadow copy with a sequence number and rotate between two rows, so the effective life doubles, and to hold a live counter in the 20 byte backup register during a brownout. That register is also the reason the brownout option matters: the part that keeps the reset enabled protects the memory but stops at 1.8 V, and the part that goes to 1.65 V gives up that reset, so the supply choice and the wear strategy are one decision rather than two.

Questions that come before the purchase order

Is the 1.65 V figure available on every reel? No. The plain order code runs from 1.8 V with the brownout reset enabled, and the D option is the part that goes to 1.65 V with that reset disabled. On a product powered from a lithium cell that difference is the usable capacity at the end of discharge, so the option letter has to be on the order, not assumed.

Does the 5 V tolerant I/O remove the need for a level translator? On the 78 lines that carry the tolerance, yes, provided the pin is configured as an input or as an open drain output. A push-pull output driven at 5 V still violates the supply relationship, and that is the mistake that shows up as a latch-up in the field. Our incoming inspection plan records the marking, the date code and the moisture level for every reel, so a mixed delivery of two temperature grades is caught at goods in rather than at the machine. The same record is what makes a traceable answer possible when a customer asks which lot a given serial number came from.