Contact Us
  • Home
  • COMPONENTS
  • Photodiode Arrays and Detector Modules for Spectrometers

Photodiode Arrays and Detector Modules for Spectrometers

A photodiode array turns a spectrum into a voltage ramp, so the pixel count and the pixel height decide the resolution and the light budget at the same time. This page lists 16, 35 and 46 element silicon arrays in ceramic DIPs, 256 to 1024 element NMOS arrays with a 2.5 mm pixel height, and a 128 pixel CMOS sensor with an internal hold. Fingertip spectrometer modules are included for instruments that need a calibrated optical bench rather than a bare die. Spectral range, pixel pitch, dark current and readout rate are given per part, because a 1 mm pitch array and a 25 micrometre pitch array are different instruments.
quote now

Product Specifications

Product Overview

A linear photodiode array replaces the exit slit and the scanning grating of a monochromator with a row of diodes on which the whole spectrum falls at once. The readout is a sequence of charges, one per pixel, so the array does three jobs that a single detector cannot: it removes the moving parts, it shortens the measurement to one integration period, and it makes the wavelength axis a fixed geometric property of the bench rather than a function of a motor.

Pixel pitch sets the optical resolution and the pixel height sets the light budget. A 25 micrometre pitch array puts 1024 pixels on 25.6 mm, which is a typical focal plane for a compact spectrograph, while a 1.0 mm pitch array puts 16 elements across 16 mm and is used where the spectrum is wide, the light is low and the resolution requirement is coarse. The 2.5 mm pixel height of the NMOS family is a light gathering feature, not a resolution feature: a taller pixel collects more photons from a tall slit image without widening the spectral band.

Readout architecture decides the support circuit. Current output NMOS arrays deliver a current per pixel, which is integrated by an external amplifier; this gives the best linearity for absorbance work but needs an integrator and a timing generator. Voltage output arrays and CMOS sensors with an internal hold deliver a rail to rail voltage and are read with a simple analog to digital converter and a clock. A sensor with a hold, such as the 128 pixel CMOS part, freezes all pixels at the same instant, which matters when the light source is pulsed or when the sample moves.

Spectral range follows the window material, not the silicon. A resin potted array covers 340 to 1100 nm, while the same die behind a quartz window reaches 190 nm, which is the difference between a visible spectrometer and one that can see the deuterium line at 254 nm. A separate family trades peak sensitivity in the near infrared for a lower capacitance, which is the version chosen when the readout speed matters more than the responsivity at 900 nm.

Detector modules shrink the whole bench into a package. A fingertip spectrometer contains the slit, the grating, the CMOS array and a sealed housing, and is quoted with a spectral resolution rather than a pixel count. That resolution is a property of the module, 12 to 15 nm across the visible range for a 256 pixel unit and 5.5 to 8 nm for a 288 pixel ultraviolet unit, so the module is chosen on the resolution and the range, and the pixel count only explains why the resolution is what it is.

Key Specifications

ParameterValueNote
Array formats16, 35 and 46 elements in ceramic DIP; 256, 512 and 1024 elements in NMOS; 128 pixels in CMOSthe format is chosen from the focal plane length and the resolution target
Spectral range, resin window340 to 1100 nmS4111-16R, peak sensitivity 960 nm
Spectral range, quartz window190 to 1100 nm on the S4111Q family, 190 to 1000 nm on the S4114 familythe quartz window is what opens the ultraviolet range
Spectral range, NMOS200 to 1000 nmpeak at 600 nm, quartz window as standard
Pixel size, 16 element array1.45 x 0.9 mm, 1.305 mm2 effective0.1 mm gap, 1.0 mm pitch
Pixel size, 35 and 46 element array4.4 x 0.9 mm, 3.96 mm2 effective0.1 mm gap, 1.0 mm pitch, 35 or 46 elements
Pixel size, NMOS25 x 2500 um25.6 mm long for 1024 pixels, 12.8 mm for 512, 6.4 mm for 256
Pixel size, CMOS linear sensor400 DPI, 8 um gap, 3524.3 um2 per pixel128 pixels over 8.12 mm of active length
Dark current, 16 element5 pA maximum at 10 mV, 25 pA at 10 Vthe reverse bias raises the dark current and the speed together
Dark current, 35 and 46 element10 pA at 10 mV and 50 pA at 10 Vten times the 16 element figure because the pixel is larger
Dark current, NMOS0.1 pA typical, 0.3 pA maximumthe low figure is what allows a long integration at room temperature
Shunt resistance2.0 GOhm minimum on the 16 element, 1.0 GOhm on the 35 and 46 element250 GOhm and 30 GOhm typical respectively
Terminal capacitance200 pF at 0 V and 50 pF at 10 V on the 16 element550 pF and 120 pF on the 35 and 46 element, 10 pF on the NMOS
Rise time0.5 us at 0 V and 0.1 us at 10 V on the 16 element, 1.2 us and 0.3 us on the larger arraysmeasured with a 1 kOhm load at 655 nm
Line rate, NMOS 10241950 lines per second maximumsets the shortest integration time in a scanning instrument
Clock rate, CMOS linear sensor5 kHz to 8 MHzthe analog to digital converter is usually the limit below 8 MHz
Integration time, CMOS linear sensor0.03375 to 100 ms33.75 us is the floor at the maximum clock rate
Dynamic range, CMOS linear sensor4000 to 1, which is 72 dBimage lag 0.5 percent typical
Supply, CMOS linear sensor3.0 to 5.5 Vsingle supply, output referenced to ground
Operating temperature-20 to +60 C on the silicon arrays, -40 to +65 C on the NMOS, -25 to +85 C on the CMOS sensorthe module family is narrower, +5 to +50 C for the visible unit
Module resolution12 nm typical and 15 nm maximum on C12666MA and C12880MA5.5 nm typical and 8 nm maximum on the 190 to 440 nm module

Included Models and Order Codes

Part numbers below are grouped by readout architecture. The suffix Q on a Hamamatsu array means a quartz window and the suffix R means a resin potting, so S4111-16R and S4111-16Q share a die and differ in the window, which is the difference between 340 nm and 190 nm at the short end. The NMOS parts share a 25 micrometre pitch and a 2.5 mm pixel height, so the pixel count alone tells the focal plane length.

PartTypeElementsPixel and pitchSpectral rangePackage
S4111-16RSi photodiode array, current output161.45 x 0.9 mm, 1.0 mm pitch340 to 1100 nm18 pin ceramic DIP, resin potting
S4111-16QSi photodiode array, current output161.45 x 0.9 mm, 1.0 mm pitch190 to 1100 nm18 pin ceramic DIP, quartz window
S4111-35QSi photodiode array, current output354.4 x 0.9 mm, 1.0 mm pitch190 to 1100 nm40 pin ceramic DIP, quartz window
S4111-46QSi photodiode array, current output464.4 x 0.9 mm, 1.0 mm pitch190 to 1100 nm48 pin ceramic DIP, quartz window
S4114-35QSi photodiode array, near infrared354.4 x 0.9 mm, 1.0 mm pitch190 to 1000 nm40 pin ceramic DIP, quartz window
S4114-46QSi photodiode array, near infrared464.4 x 0.9 mm, 1.0 mm pitch190 to 1000 nm48 pin ceramic DIP, quartz window
S3904-256QNMOS linear image sensor, current output25625 x 2500 um, 25 um pitch200 to 1000 nmceramic, quartz window
S3904-512QNMOS linear image sensor, current output51225 x 2500 um, 25 um pitch200 to 1000 nmceramic, quartz window
S3904-1024QNMOS linear image sensor, current output102425 x 2500 um, 25 um pitch200 to 1000 nmceramic, quartz window, 1950 lines/s
TSL1401CLCMOS linear sensor array with hold128400 DPI, 8 um gap400 to 1000 nmCL-8, 3.0 to 5.5 V, 8 MHz
C12666MAFingertip spectrometer module25612.5 x 1000 um, slit 50 x 750 um340 to 780 nm20.1 x 12.5 x 10.1 mm, 5 g
C12880MAFingertip spectrometer module28814 x 200 um, slit 50 x 500 um340 to 850 nm20.1 x 12.5 x 10.1 mm, 5 g
C16767MAFingertip spectrometer module, ultraviolet28814 x 200 um, slit 15 x 500 um190 to 440 nm20.1 x 12.5 x 10.1 mm, 5 g

Choosing the Readout Architecture

The four architectures below are not interchangeable at the circuit level, even when two of them look identical on a datasheet. The choice is made once, at the point where the analog front end is fixed, because changing it later means a new board and a new timing generator.

ArchitectureOutput per pixelSupport circuitBest forLimitation
Current output NMOS, S3904 familyPhotocurrent, integrated externallyIntegrator, timing generator, 5 V pulsesAbsorbance and low light work where linearity mattersNeeds a low noise integrator and careful reset timing
Voltage output NMOS, S3921 to S3924 familyVoltage ramp, internally bufferedClock and analog to digital converterCompact instruments that cannot carry an integratorLinearity is slightly lower than the current output type
CMOS linear sensor with hold, TSL1401CLRail to rail voltage, all pixels heldSerial input, clock, analog to digital converterPulsed sources and moving samples128 pixels only, 400 DPI
Fingertip spectrometer module, C12666MA and C12880MADigital spectrum after the internal arrayClock, start pulse, analog to digital converterHandheld and inline instruments with a fixed benchResolution is fixed by the module, 12 to 15 nm

Key Features

Pixel height for light budget – The NMOS family uses a 2.5 mm pixel height, which collects more light from a tall slit image without widening the spectral band.

Pitch for resolution – A 25 micrometre pitch puts 1024 pixels on 25.6 mm, while a 1.0 mm pitch spreads 16 elements over 16 mm for coarse, low light work.

Quartz window for the ultraviolet – The Q suffix opens 190 nm, which is where a deuterium lamp and a 254 nm line live, and the R suffix stops at 340 nm.

Low dark current for long integration – 0.1 pA typical on the NMOS family allows an integration of seconds at room temperature without a cooler.

Internal hold for pulsed sources – The 128 pixel CMOS sensor freezes all pixels at one instant, so a flash lamp does not smear across the readout.

Line rate for scanning instruments – 1950 lines per second on the 1024 element NMOS array sets the shortest integration time and the maximum scan speed.

Module with a stated resolution – The fingertip modules are quoted at 12 to 15 nm in the visible range and 5.5 to 8 nm in the ultraviolet, which is the number an instrument specification needs.

One die, two windows – S4111-16R and S4111-16Q are the same array with different windows, so a bench can be moved from visible to ultraviolet without a new layout.

Applications

The same arrays appear in three instrument types, and the difference between them is the readout, not the silicon.

Diode array spectrophotometers – A 1024 element NMOS array covers 200 to 1000 nm in one integration, which is what allows a full spectrum to be captured before a reaction moves.

Handheld and inline analysers – A fingertip module with an internal bench removes the optical alignment step, so a colour or concentration reading can be built into a handset.

Emission and fluorescence readers – A 16 or 46 element array with a 1.0 mm pitch reads a wide, low level band, which suits a compact fluorimeter with no moving grating.

Colour and display measurement – A 256 pixel module in the visible range measures a display or a print patch against a reference, with the resolution stated in nanometres.

These arrays are used on SUPERB PCB and SUPERB PCBA spectrometer boards, where the analog front end is laid out around the pixel rate.

Sourcing and Cross-Reference

Array sourcing is driven by the optical bench rather than by the electronics, because the pixel pitch and the package height are fixed by the focal plane that already exists. A substitution is only practical when pitch, pixel height, window material and package footprint all match, and the fourth field is the one that usually fails: two arrays with the same 25 micrometre pitch can sit in packages with different pin rows, which means a new board.

Where a part is marked not recommended for new builds, the practical route is a last time buy against the production forecast and a parallel qualification of the successor. Hamamatsu keeps long product lives on this family, but the quartz window versions and the ultraviolet modules are the lines that move first, so the buffer is held on those rather than on the visible parts.

Spectrometer modules carry a wavelength calibration that is written at the module level, so two modules are not interchangeable in software even when the model number matches. The calibration factors are supplied per serial number, and a replacement module needs its own factors loaded before the instrument is released. That is the reason a module order is placed with the serial numbers recorded, and the reason a spare is kept calibrated rather than in a bare box.

The module and its flex are kitted together for SUPERB Assembly builds, so the calibration sheet travels with the unit.

Q: Can you supply a pin compatible array with the same pixel pitch and a quartz window?

A: SUPERB Tech confirms the window material and the readout type before quoting, because the same array is sold in both versions.

Why Buy Detector Arrays Through SUPERB

  1. Pitch and package checked together: A cross reference is only proposed when pitch, pixel height, window and footprint match, so the board does not have to change.
  2. Window option on the same die: The resin and quartz versions of one array are quoted side by side, which is what a range extension from visible to ultraviolet needs.
  3. Module and array in one order: A bare array for the production bench and a calibrated module for the handheld version can be sourced together.
  4. Long life parts held for build: The ultraviolet modules and the quartz window arrays are the lines kept in buffer, because they are the ones with the longest qualification tail.
  5. Serial numbers recorded: Module shipments are booked with the serial number, so the wavelength factors can be matched to the unit that was built.
  6. Support for the analog front end: The readout type is confirmed before the order, because a current output array and a voltage output array need different integrators.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Monochromator Gratings and Optical Bench Parts, Lamp Housings and Shutters, Xenon and Deuterium Lamps, UV and Visible LED Sources, PIN and Avalanche Photodiodes, Quartz Flow Cells and Cuvettes, Component Lead Time Solutions.

Actual product photos available on request