Contact Us
  • Home
  • COMPONENTS
  • Xenon and Deuterium Lamps for Photometric Instruments

Xenon and Deuterium Lamps for Photometric Instruments

A photometer is a lamp with an optical bench in front of it, and the lamp sets both the wavelength range and the noise floor. Deuterium covers the deep UV with a continuum that reaches 115 nm on a fluoride window; xenon covers 185 nm to 2,000 nm with a small, bright arc. The parts below run from a 75 W xenon arc with a 1.3 mm source size up to a 300 W forced air lamp, and from a 2,000 hour long life deuterium body down to a 1,000 hour high intensity type. Window material is the number that decides the short wavelength cut off: UV glass stops at 185 nm, synthetic silica reaches 160 nm, and a magnesium fluoride window reaches 115 nm. Each line gives the drive figures, the guaranteed life and the trigger voltage together, because a lamp that matches the optics and not the starter will not light.
quote now

Product Specifications

Product Overview

Two lamp types cover most photometric instruments, and they are not interchangeable in either spectrum or drive. A deuterium lamp runs an arc in deuterium gas at low pressure and emits a molecular continuum that rises through the UV and fades past 400 nm. It is the standard source for absorbance between 190 and 400 nm, which is where most of the organic chromophores and most of the pharmacopoeial methods sit. A xenon short arc lamp runs a high pressure arc in xenon and emits a continuum from 185 nm to about 2,000 nm with a very small source. It is the standard source where a compact, bright point is needed and where the near infrared also matters.

The window is the first thing to read on a data sheet. A deuterium lamp with UV glass transmits from 185 nm, one with synthetic silica from 160 nm, and one with a magnesium fluoride window from 115 nm. The arc inside is the same; the envelope is what changes. That matters when an instrument is specified at 190 nm and then fitted with a lamp that is quoted from 185 nm, because the margin at the short end is then a window question rather than a lamp question. The same logic applies at the long end of a xenon lamp, where the fused silica envelope and the low ozone version of it differ in the deep UV.

Drive is the second thing, and it is where replacement lamps go wrong. A deuterium lamp is run at a fixed anode current, 300 mA on most analytical bodies, with a tube drop of 75 to 85 V, and it needs a starter that can deliver 350 to 500 V to break down the gas. It also has a filament that is warmed at 2.5 V for about 20 seconds and then held at 1.0 V while the lamp runs. A xenon lamp needs a trigger of 15 to 20 kV and a supply that limits current after the arc strikes. A lamp with the right wattage and the wrong trigger simply does not light, and a supply with the right voltage and the wrong current shortens the arc life.

Life is quoted in a way that surprises people. The guaranteed figure is the time at which output at 230 nm falls to half of its initial value, or the time at which the short term fluctuation exceeds a stated limit. A lamp at that point still lights and still looks bright to the eye; it is simply half as bright as it was in the region the method uses. For a ratio instrument the change is partly corrected, for a single beam instrument it is not, so the replacement interval is usually set from lamp hours rather than from a reading. Warm up is the other half of the same story: a deuterium body needs 20 to 30 minutes to reach thermal equilibrium, and a measurement taken at five minutes is a measurement of a lamp that is still moving.

Key Specifications

ParameterValueNote
Spectral range, deuterium115 to 400 nm on a fluoride window, 160 to 400 nm on synthetic silica, 185 to 400 nm on UV glassthe arc is the same, the envelope sets the short end
Spectral range, xenon185 to 2,000 nmlow ozone silica extends the deep UV at the cost of some output
Deuterium anode current300 mA dc, plus or minus 30 mA on the L2D2 bodiesthe current is regulated, not the voltage
Deuterium tube drop75 to 85 V dc depending on the bodya 300 mA lamp therefore runs at about 24 W
Deuterium starting voltage350 V dc on most bodies, 500 V dc on the water cooled 200 W typethe starter has to reach this before the arc strikes
Filament sequence2.5 V at 4 to 5.8 A for about 20 s, then 1.0 V at 1.8 A, or 3 to 6 V at 0.3 to 0.45 A on the long life bodya supply built for one sequence will not run the other
Aperture0.5 mm or 1.0 mm on the deuterium bodies0.5 mm suits a narrow slit and a small detector
Xenon ratings75 W, 100 W, 150 W and 300 Warc length runs 1.3 mm to 3.0 mm with the rating
Xenon voltage and current15 to 20 V dc at 5.4 to 15 Athe supply is a current limited source, not a fixed voltage
Xenon trigger15 kV on the 75 W body, 20 kV on the 150 W bodiesa 20 kV starter will not harm a 15 kV lamp, the reverse is not true
Output noise0.005 percent peak to peak on a long life deuterium body, 1 percent peak to peak maximum on xenonnoise is often the supply rather than the lamp
Driftplus or minus 0.5 percent per hour on the long life deuterium bodies and on xenona ratio instrument corrects part of it, a single beam does not
Guaranteed life1,000 to 2,000 h on the analytical bodies, 4,000 h on the long life series, 500 h on the vacuum UV typesend of life is 50 percent of initial output at 230 nm
Warm up20 to 30 minutes to thermal equilibrium on a deuterium bodya reading taken earlier is taken on a moving lamp
Coolingconvection on the 75 W to 150 W xenon bodies, forced air on the 300 W body, water on the 200 W deuterium typethe cooling method is part of the lamp rating, not an accessory

Included Models and Order Codes

The table is split by lamp type, deuterium first and xenon second, because the two are chosen for different ranges and cannot be compared line by line. Deuterium lines carry the window material and the aperture, which are the two facts that decide whether a body fits an existing housing. Xenon lines carry the arc length and the trigger voltage, which decide whether the optics and the starter can accept it.

LampTypeSpectral rangeAperture or arcDriveLifeNote
Hamamatsu L6565Deuterium, UV glass185 to 400 nm1.0 mm aperture300 mA, 80 V2,000 h guaranteedstandard body for a bench spectrophotometer
Hamamatsu L6301Deuterium, synthetic silica160 to 400 nm1.0 mm aperture300 mA, 80 V2,000 h guaranteeddeeper UV than the glass window body
Hamamatsu L6302Deuterium, synthetic silica160 to 400 nm0.5 mm aperture300 mA, 80 V2,000 h guaranteedsmall aperture for a narrow slit
Hamamatsu L7293Deuterium, magnesium fluoride115 to 400 nm1.0 mm aperture300 mA, 80 V2,000 h guaranteedvacuum UV, 350 V dc starting
Heraeus DX 202 R, 80001131Deuterium, fused silica185 to 400 nm1.0 mm aperture300 mA, 80 V2,000 h guaranteed0.005 percent noise, 2.5 V 5.8 A warm up
Heraeus DX 201/05 RJ, 80008685Deuterium, fused silica185 to 400 nm0.5 mm aperture300 mA, 80 V2,000 h guaranteedsame body as DX 202 R with a small aperture
Heraeus DX 246, 80006934Deuterium, fused silica185 to 400 nm1.0 mm aperture300 mA, 80 V2,000 h guaranteed10 to 12 V 0.8 to 1.0 A warm up supply
Heraeus DO 605 T, 80052430Deuterium, synthetic silica160 to 400 nm1.0 mm aperture300 mA, 75 V1,000 h guaranteedhigher intensity, shorter life than DX
Heraeus DO 660/05 J, 45002349Deuterium, synthetic silica160 to 400 nm0.5 mm aperture300 mA, 85 V1,000 h guaranteednarrow slit version of the high intensity body
Heraeus D 200 F, 56001671Deuterium, water cooled160 to 400 nm1.0 mm aperture0.9 to 1.8 A, 110 V1,000 h guaranteed200 W class, needs the cooling jacket
Hamamatsu L2174Xenon short arc185 to 2,000 nm1.3 mm arc5.4 A, 15 V1,000 h guaranteed, 2,000 h average75 W, 15 kV trigger, 15 g, convection cooled
Hamamatsu L2175Xenon short arc185 to 2,000 nm2.5 mm arc7.5 A, 19 V1,200 h guaranteed, 2,500 h average150 W, 20 kV trigger, 45 g
Hamamatsu L2273Xenon short arc, quiet cathode185 to 2,000 nm2.0 mm arc8.5 A, 17 V1,800 h guaranteed, 3,000 h average150 W, 20 kV trigger, 45 g, stable arc point
Hamamatsu L11307Xenon short arc185 to 2,000 nm1.3 mm arc7.0 A, 15 Vnot published in the sheet read100 W, small source for a compact bench
Hamamatsu L2479Xenon short arc185 to 2,000 nm3.0 mm arc15 A, 20 Vnot published in the sheet read300 W, forced air cooling

Reading the Life and Output Numbers

Four numbers decide whether a lamp will behave in an instrument: the life definition, the noise, the aperture and the trigger. This table is the short form used when a data sheet is read against a method.

NumberWhat it meansWhat to check before ordering
Guaranteed lifehours until output at 230 nm falls to 50 percent of the initial value, or until fluctuation exceeds the stated limitthe lamp still lights at that point, so a bench test will not show it
Average lifetypical value across a population, usually 1.5 to 2 times the guaranteed figureplan replacement from lamp hours, not from the average
Noise, peak to peakshort term variation, 0.005 percent on a long life body and up to 1 percent on xenona noisy trace is often the supply or the arc position, not an old lamp
Driftlong term change per hour, plus or minus 0.5 percent on the bodies listed herea ratio instrument corrects it, a single beam instrument shows it
Aperturethe emitting area that the optics see, 0.5 mm or 1.0 mm on deuteriuma 0.5 mm body in a wide slit loses light; a 1.0 mm body in a narrow slit wastes it
Arc lengththe source size for imaging, 1.3 mm to 3.0 mm on xenona 3 mm arc does not image into a 1 mm slit without loss
Trigger voltage15 or 20 kV on xenon, 350 to 500 V on deuteriumthe starter is matched to the lamp, not to the wattage
Warm up20 to 30 minutes to thermal equilibrium on deuterium, minutes on xenona method run immediately after power on is run on a moving baseline

Key Features

Window chosen for the short end – UV glass at 185 nm, synthetic silica at 160 nm and magnesium fluoride at 115 nm on the same arc body, so the range is a window decision

Aperture of 0.5 mm or 1.0 mm – two emitting areas in one family, which lets a narrow slit instrument and a wide slit instrument share a housing

Long life body at 2,000 h and a 4,000 h series – the analytical bodies are quoted at 2,000 h guaranteed, and the extended series doubles that

Xenon from 75 W to 300 W – arc length from 1.3 mm to 3.0 mm, so a compact bench and a larger instrument are covered by one range

Trigger voltage on the sheet – 15 kV or 20 kV stated per body, because a starter that cannot reach it leaves the lamp dark

Two filament sequences supported – 2.5 V warm up at 4 to 5.8 A, or 10 to 12 V at 0.8 to 1.0 A, so an existing supply can be matched

Water cooled 200 W deuterium type – a high power body with a cooling jacket for instruments that need more UV output than a 30 W arc gives

Life defined against a wavelength – the 50 percent figure is at 230 nm and 300 mA, which is the region a UV method actually uses

Applications

These lamps sit at the front of an optical bench, and the bench is built around the source size and the spectrum. The three cases below are the ones that fix the lamp type, the window and the drive.

UV visible spectrophotometry – a deuterium lamp for 190 to 400 nm and a tungsten halogen lamp for the visible, switched at about 360 nm. The 2,000 h body is the usual replacement, and the aperture is chosen against the slit width of the monochromator.

HPLC and flow analysis detectors – a deuterium body with a 0.5 mm aperture and a low volume flow cell. The lamp is run at a fixed 300 mA and the drift figure matters more than the absolute output, because the detector measures a ratio.

Water, gas and process photometers – a xenon flash or continuous arc where a compact source and a near infrared path are needed, or a deuterium body where the method is a UV absorbance at a single wavelength. The trigger voltage and the cooling method decide whether the housing can take the lamp.

The lamp driver and the detector board behind these sources are the kind of build SUPERB PCB and SUPERB PCBA programmes cover, from the high voltage starter to the transimpedance stage.

Sourcing and Cross-Reference

A lamp is ordered by body number, not by wattage, because the same wattage exists in several envelopes with different windows and apertures. The housing, the slit and the starter are the fixed points, and the lamp is chosen to fit them rather than the other way round.

Where a lamp is obsolete, the drive is the constraint. A body with the same spectrum and a different filament sequence will not run on the existing supply, and a xenon lamp with the same wattage and a different trigger will not strike. We compare the current, the warm up voltage and the trigger before naming a replacement.

Ageing stock is a real risk with lamps, so the date code and the storage are part of the question. A lamp that has been on a shelf for years is not the same as one from the current batch, and the guaranteed life runs from first strike rather than from the invoice date. We state the batch and the date code on the delivery file.

A lamp, its housing gasket and the connector are ordered as one set when an instrument is down, which is how SUPERB Assembly ships a replacement.

Q: Can you match a deuterium lamp by window material, aperture and filament sequence when the original body is discontinued?

A: SUPERB Tech can compare the window, the aperture and the filament sequence against the old body before an order is released.

Why Buy Lamps from SUPERB

  1. Window and aperture asked first: the short wavelength limit and the emitting area decide whether a body fits the instrument, so both are confirmed before a part is named
  2. Drive figures on every line: current, voltage, warm up and trigger appear together, which is what stops a lamp that fits the housing and not the supply
  3. Life defined at a wavelength: the 50 percent point at 230 nm is quoted as the maker states it, not as a round number
  4. Batch and date code on the paperwork: a lamp is a consumable with a shelf history, and the file says which batch was shipped
  5. Deuterium and xenon on one list: a single source for the UV body and the xenon arc, which keeps an instrument build on one purchase order

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Bandpass and Interference Filters for Photometric Channels, UV and Visible LED Sources for Photometric Detection, Quartz Flow Cells and Cuvettes for Photometric Instruments, Turbidity and Photometric Detector Modules for Water Analysis, High Power LED Emitters for Illumination and Infrared, Component Lead Time Solutions.