Filter Wheels and Automated Filter Changers
Product Specifications
Product Overview
A filter wheel is bought against two optics numbers and one timing number. The optics numbers are the filter diameter and the filter thickness: a 25.4 mm filter in a mounted ring needs a slot depth of about 7 mm, while bare glass needs a retaining ring and a thickness under 6.35 mm. The timing number is how long the experiment can wait between two wavelengths.
Wheels divide into three groups. A six position wheel for 25 mm filters is the workhorse for photometry and fluorescence, and the fastest of them change position in 55 ms, which is what ratio imaging needs. A twelve position wheel for 12.5 mm filters puts a finer set of narrow band filters in the same housing. Manual stations hold one or two wheels on detents, and are used where the filter set is fixed for the day and electronics would only add a failure point.
Control is where integration effort lives. USB and RS-232 wheels come with a command set and a small application, and can be driven from a script. A BNC or TTL trigger wheel takes a pulse from the camera, which is the shorter path when the imaging software already owns the timing. Flange mounted wheels take the third route: a 1.5 inch series male and female flange couples the wheel directly to a monochromator or lamp housing, with no post and no adapter.
Key Specifications
| Parameter | Value | Notes |
|---|---|---|
| Wheel positions | 5, 6 or 12 | Model dependent |
| Filter diameter | 25.4 mm or 12.5 mm | 25 mm optics also fit a 1 inch slot |
| Maximum filter thickness | 4 to 15.24 mm | 6.35 mm on stepper wheels, 4 mm on manual stations |
| Clear aperture | 22.2 to 22.9 mm at 25 mm, 10.2 mm at 12.5 mm | Detector side aperture |
| Switching time | 55 ms to 2.5 s | Adjacent position, model dependent |
| Repeatability | plus or minus 2 degrees | Stepper driven wheels |
| Rated cycles | 1.5 million minimum | C series motorized wheels |
| Control interfaces | USB, RS-232, BNC trigger, TTL | Model dependent |
| Mounting | SM1 thread, 30 mm cage, 8-32 or M4 taps | Manual stations use SM1 and SM05 |
| Flange type | 1.5 inch series male and female | Monochromator mounted wheels |
Included Models and Order Codes
The table is grouped by drive: stepper motor wheels with an integrated controller, the fast change wheel that needs its own controller, manual stations on detents, and flange mounted wheels for spectrometers. Clear apertures are given because the aperture, not the filter diameter, sets how much of a small source reaches the detector.
| Part Number | Type | Filter Size | Clear Aperture | Switching Time | Control |
|---|---|---|---|---|---|
| FW102C | Motorized, 6 position | 25.4 mm, 6.35 mm thick | 22.9 mm | Under 1 s adjacent, 2.5 s other | USB, RS-232, BNC |
| FW102CNEB | Motorized, 6 position | 25.4 mm | 22.9 mm | Under 1 s adjacent | Preloaded ND 0.5 to 4.0 |
| FW212C | Motorized, 12 position | 12.5 mm, 6.35 mm thick | 10.2 mm | Under 0.5 s adjacent | USB, RS-232, BNC |
| FW212CNEB | Motorized, 12 position | 12.5 mm | 10.2 mm | Under 0.5 s adjacent | Preloaded ND 0.1 to 4.0 |
| FW103H | Motorized fast change, 6 position | 25.4 mm, 6.35 mm thick | 22.9 mm | 55 to 60 ms | BSC201 controller, trigger out |
| FW1A | Manual station, one wheel | 25.4 mm, 4 mm thick | 23 mm | Detent, 6 positions | SM1 threads |
| FW2A | Manual station, two wheels | 25.4 mm, 4 mm thick | 23 mm | 36 combinations | SM1 threads |
| FW2B | Manual station, two wheels | 12.5 mm, 4 mm thick | 11 mm | 144 combinations | SM05 threads |
| 74010 | Motorized, 6 position | 25.4 mm, 2.5 to 10.2 mm thick | 23 mm | Under 2 s | Monochromator command |
| USFW-100 | Motorized, 6 position | 25.4 mm, 1 to 15.24 mm thick | 22.2 mm | 0.9 degree per step | USB 2.0 |
| 74040 | Motorized system, 6 position | 25.4 mm | 22 mm | Under 2 s | TTL pulses |
| 74041 | Motorized system, 6 position | 25.4 mm | 22 mm | Under 2 s | RS-232, GPIB |
| 77370 | Manual, 5 position | 25.4 mm, 1.5 to 12.7 mm thick | 22 mm | Knurled knob, detent | 1.5 inch flange |
Key Features
Six filters on one axis – empty, 0.5, 1.0, 2.0, 3.0 and 4.0 OD can sit in the beam without touching the bench
Sub second switching – 55 ms on the fast change wheel, under 0.5 s on the twelve position wheel
Light tight housing – the fast change wheel uses a hall effect sensor and a closed cover, so no light leaks during an exposure
Manual stations for fixed sets – detents hold position without electronics, up to 144 combinations on two wheels
Flange mount for spectrometers – 1.5 inch series male and female flanges couple the wheel to a monochromator or lamp housing
Trigger in and out – BNC lines synchronise the wheel with a camera or a detector, in either direction
Applications
The wheel is chosen by what has to change during a run: wavelength, attenuation level, or order sorting after a monochromator.
Fluorescence imaging – multi wavelength excitation and emission with 25 mm filters in six slots
Photometry and colorimetry – neutral density steps in front of a detector to keep it inside its linear range
Order sorting after a monochromator – a wheel of long pass filters behind the exit slit of a scanning instrument
Filter wheels are supplied alongside SUPERB PCB and SUPERB PCBA work when a detection bench needs its wheel and its driver board as one build.
Sourcing and Cross-Reference
The first mistake in a filter wheel order is a thickness mismatch. A filter mounted in a 5 mm ring will not sit flat in a slot rated for 6.35 mm of glass, and a 10 mm mounted filter needs the flange type wheel rather than the stepper wheel. The second is the aperture: a 10 mm clear aperture on a twelve position wheel cuts the beam of a source that was sized for a 22 mm port.
Timing decides the drive. A stepper wheel with an integrated controller is the simplest choice when the filter changes once per scan, and a fast change wheel is needed when two exposures are compared within a few milliseconds. The rated cycle count belongs in the same comparison, because a wheel that is cycled every frame for a year is a different duty from one that is set once a day.
Where the wheel has to sit inside an existing optical train, the flange is the interface. A 1.5 inch series flange takes the wheel directly onto a monochromator or a lamp housing, while an SM1 threaded port takes it onto a lens tube. We quote the wheel, the controller and the adapter as one line so the mounting is not discovered at installation.
Wheel, controller and cable set are packed through SUPERB Assembly as a single line item.
Q: Can you supply a six position wheel that fits a monochromator flange and takes 25 mm filters?
A: Yes. SUPERB Tech quotes the wheel with its flange and controller, and states the clear aperture and switching time on the quotation.
Why Choose SUPERB for Filter Wheel Assemblies
- Aperture stated: clear aperture is quoted with the filter size, so the beam is not clipped by the housing
- Timing stated: adjacent and full travel times are both given, which is what a sequence actually sees
- Control options: USB, RS-232, TTL and BNC variants on one page, so the interface is a choice rather than a constraint
- Manual and motorized: a detent station is quoted where electronics would add cost without adding a function
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Bandpass and Interference Filters, Neutral Density Filters and Reference Standards, Dichroic Filters and Beam Splitters, Optical Slits and Apertures, Monochromator Gratings and Optical Bench Parts, Photodiode Arrays and Detector Modules.