Contact Us
  • Home
  • COMPONENTS
  • Optical Slits and Apertures for Monochromator Entrances

Optical Slits and Apertures for Monochromator Entrances

An entrance slit sets two things at once, the spectral band that reaches the grating and the amount of light that reaches the detector. This page covers stainless steel slit foils from 5 to 500 micrometres, in 3 mm and 10 mm lengths, mounted in half inch or one inch housings or supplied bare. Width tolerance is given per band because a 5 micrometre slit is held to one micrometre while a 500 micrometre slit is held to ten. The same parts are used as exit slits, as aperture stops and as reference edges for knife edge scans.
quote now

Product Specifications

Product Overview

The entrance slit of a monochromator is a compromise that is fixed mechanically and cannot be adjusted once the instrument is built. A wider slit passes more light and a narrower slit passes a narrower band, and the two cannot both be improved at the same time. The band that reaches the detector is the slit width multiplied by the dispersion of the bench, so on a bench that spreads 10 nm across each millimetre, a 100 micrometre slit passes a 1 nm band and a 10 micrometre slit passes a 0.1 nm band at one tenth of the light.

For a compact instrument the slit width is chosen from the detector, not from the grating. A photodiode array with a 25 micrometre pixel pitch already samples the focal plane every 25 micrometres, so a slit narrower than one pixel does not add resolution, it only removes light. That is why a compact spectrograph with a 1024 element array is usually fitted with a 20 to 50 micrometre slit, while a scanning monochromator with a photomultiplier can use a 10 micrometre slit and gain resolution at the cost of signal.

Mechanical quality matters as much as width. A slit cut in 50 micrometre stainless foil has two edges that are close enough together to diffract the light that passes, and any burr or taper shows up as a shoulder on the band profile. The foils on this page are black oxide treated on both sides, which reduces the light that scatters off the face around the opening, and widths of 40 micrometres and below are counterbored so the material around the opening is thinner and the edge is cleaner.

Mounting is the second decision. A half inch mounted slit fits a SM05 lens tube and is the standard for a compact bench, a one inch mounted slit fits a larger tube and is used where the beam is wider, and a bare foil is used inside a custom holder or where the slit is placed against a detector window. The 3 mm length matches a beam that is tall and narrow, and the 10 mm length is used where the beam is spread by a cylindrical lens or where the slit is also the field stop.

An aperture is not only a slit. The same foil family includes round pinholes and half aperture foils for knife edge scans, and the choice between a slit and a pinhole depends on whether the bench images a line or a point. A slit passes a line image and keeps the height of the detector illuminated, while a pinhole defines a point and is used for alignment, for confocal work and for measuring a point spread function.

Key Specifications

ParameterValueNote
Slit width range5 to 500 um3 mm length covers 5 to 500 um, 10 mm length covers 20 to 500 um
Slit length3 mm or 10 mm3 mm for a line image, 10 mm where the beam is spread
Width tolerance, 5 to 10 um+/- 1 umthe tightest band in the range
Width tolerance, 15 um+/- 1.5 um10 percent of nominal
Width tolerance, 20 to 30 um+/- 2 umused for the common compact bench widths
Width tolerance, 40 to 50 um+/- 3 umthe band where counterboring starts
Width tolerance, 100 to 200 um+/- 4 umthe workhorse band for array spectrographs
Width tolerance, 500 um+/- 10 umwidest opening, used for throughput at low resolution
Foil thickness50 um300 series stainless steel, black oxide conversion coating on both sides
Foil diameter9.6 mm, which is 0.38 inthe bare foil drops into a half inch holder
Housing diameter12.7 mm or 25.4 mmhalf inch or one inch, black anodized 6061-T6 aluminium
Housing thickness2.5 mm, which is 0.10 inthe front face is engraved with the part number and the width
Counterboreincluded on widths of 40 um and belowthinner material at the edge gives a cleaner band profile
Air slit thickness, Edmund precision0.01 mm nominal100 um wide, 3.0 mm long, stainless steel
Air slit outer diameter9.5 mm unmounted, 25.0 mm mountedthe mounted version is sealed into a black anodized mount
Air slit centring+/- 125 um from the mount centrestated on the mounted part, not on the bare foil
Air slit width tolerance+/- 5 um at 100 umwider than the foil family at the same nominal width

Included Models and Order Codes

Part numbers follow the housing and the length. The H in a Thorlabs code marks a half inch housing, the K marks a one inch housing where the code ends in K, and the UL marks an unmounted foil with a 10 mm length. The number before the letter is the nominal width in micrometres, so S20HK is a 20 micrometre slit in a half inch mount and S20ULK is the same width as a bare 10 mm foil. The Edmund codes below are catalogue numbers rather than width codes, so the width has to be read from the description.

PartWidthLengthFormatNote
S5HK5 um +/- 1 um3 mm12.7 mm mounted housingnarrowest stocked slit, counterbored
S10HK10 um +/- 1 um3 mm12.7 mm mounted housingused for high resolution scanning benches
S15HK15 um +/- 1.5 um3 mm12.7 mm mounted housingbetween the 10 and 20 um steps
S20HK20 um +/- 2 um3 mm12.7 mm mounted housingcommon with a 25 um pitch array
S50HK50 um +/- 3 um3 mm12.7 mm mounted housingthroughput option for a compact bench
S100K100 um +/- 4 um3 mm25.4 mm mounted housinglarger housing for a wider beam
S200K200 um +/- 4 um3 mm25.4 mm mounted housinglow resolution, high light
S500K500 um +/- 10 um3 mm25.4 mm mounted housingwidest opening in the series
S20ULK20 um +/- 2 um10 mmbare foil, 12.7 mm diameterfor a custom holder or a detector window
S50ULK50 um +/- 3 um10 mmbare foil, 12.7 mm diameter10 mm length gives a taller line image
S100ULK100 um +/- 4 um10 mmbare foil, 12.7 mm diameterused ahead of a cylindrical lens
4372100 um +/- 5 um3 mmbare foil, 9.5 mm diameterEdmund precision air slit, 0.01 mm foil
15399100 um +/- 5 um3 mm25.0 mm mountedEdmund air slit, centring +/- 125 um

Which Length and Housing to Order

The four format groups below cover the same widths in different mechanical packages. The format is decided first, because a bare foil cannot be screwed into a lens tube and a mounted slit cannot be bonded against a detector window without removing the foil from its housing.

FormatSlit lengthOuter diameterFixingTypical position
Mounted in a half inch housing3 mm12.7 mmSM05 thread, 2.5 mm thick bodyentrance slit of a compact spectrograph
Mounted in a one inch housing3 mm25.4 mmone inch mount, 2.5 mm thick bodybench with a wider beam or a larger grating
Bare foil, half inch diameter10 mm12.7 mmclamped between two platescustom holder or the face of a detector
Mounted in a one inch housing10 mm25.4 mmone inch mounttall line image, field stop duty
Precision air slit, unmounted3 mm9.5 mmclamped, 0.01 mm foilalignment and point spread measurement
Precision air slit, mounted3 mm25.0 mmsealed into a black anodized mountbench where the slit must be swapped quickly

Key Features

Width bands with stated tolerance – 5 and 10 micrometres are held to one micrometre, 20 and 30 to two, 100 and 200 to four, and 500 to ten.

Two slit lengths – 3 mm for a line image on a compact bench and 10 mm where the beam is spread by a lens or the slit doubles as a field stop.

Black oxide on both faces – The coating absorbs the light that scatters off the foil face around the opening, which lowers the stray light floor.

Counterbored narrow slits – Widths of 40 micrometres and below are thinned around the opening so the edge is sharper and the band profile is cleaner.

Housings that fit standard tubes – Half inch and one inch black anodized aluminium bodies drop into the lens tubes already on the bench.

Bare foils for custom holders – The same slit is available unmounted in a 9.6 mm foil, which is the form used against a detector window or inside a machined block.

Engraved identification – The front face carries the part number and the width, so a slit that is swapped during service is not mixed up with another width.

Wide and narrow in one range – 5 micrometres to 500 micrometres from one family means the same holder and the same handling for a high resolution and a high light bench.

Applications

Slits sit in three places in an optical instrument, and each one is chosen for a different reason.

Monochromator entrance – The entrance slit defines the band that reaches the grating, so the width is chosen against the dispersion of the bench and the pixel pitch of the detector.

Exit slit and order sorting – A second slit at the exit passes one band and blocks the rest, which is how a scanning instrument rejects stray light from adjacent orders.

Alignment and knife edge scans – A bare foil with a 10 or 20 micrometre opening is scanned across a focus to measure the spot, which is the cheapest way to check a bench after service.

Detector field stop – A slit bonded against a detector window limits the area that sees light and keeps a stray reflection from reaching the active pixels.

Slits are fitted to the optical benches on SUPERB PCB and SUPERB PCBA analyser builds, where the entrance slit is aligned before the grating is fixed.

Sourcing and Cross-Reference

Slits are low value parts with a high cost of error, because a slit of the wrong width is not visible on the bench and only shows up as a resolution or a signal problem. The order is therefore placed on the width, the length, the format and the tolerance together, and the tolerance is the field that a general catalogue number does not carry. A 100 micrometre slit at plus or minus 4 micrometres and a 100 micrometre air slit at plus or minus 5 micrometres are used in different places even though both are called 100 micrometres.

Where a bench is copied from an existing instrument, the slit is often the part that is hardest to trace, since it is engraved with a width rather than a maker code. The practical route is to measure the old foil under a toolmaker microscope and match the width, the length and the outer diameter, then choose the nearest catalogue band. A foil that measures 98 micrometres is a 100 micrometre part within tolerance, not a custom width.

Delivery is short on the stocked widths and longer on the extremes. The 5 micrometre and 500 micrometre ends of the range are the lines that run out first, so a production instrument that uses one of them keeps a buffer rather than ordering against the line. The mounted and unmounted versions of the same width are also stocked separately, which is why a bare foil is not a substitute for a mounted part when a tube mount is what the bench has.

The slit, the holder and the retaining ring are kitted as one set for SUPERB Assembly, so a service swap does not need three part numbers.

Q: Can you supply a slit in the same width and outer diameter as the one already on our bench?

A: SUPERB Tech asks for the outer diameter and the slit length before quoting, because the same width is stocked in four mechanical formats.

Why Buy Optical Slits Through SUPERB

  1. Width and tolerance together: The tolerance band is quoted with the width, so a replacement is the same part and not only the same nominal number.
  2. Format matched to the bench: Half inch, one inch, bare foil and air slit formats are quoted together, which is what a bench with mixed mounts needs.
  3. Optics and electronics in one place: The slit can be ordered with the grating, the lamp and the detector that share the same optical path.
  4. Small parts without a minimum: A single foil or a small pack is supplied, which suits a service spares shelf rather than a production line.
  5. Traceable width for service records: The engraved width and the maker code are recorded on the shipment, so a service report can name the part that was fitted.
  6. Support on the optical choice: The width is confirmed against the dispersion and the detector pitch before the order, because a narrower slit is not always a better one.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Monochromator Gratings and Optical Bench Parts, Lamp Housings and Shutters, Xenon and Deuterium Lamps, UV and Visible LED Sources, Quartz Flow Cells and Cuvettes, Turbidity and Photometric Detector Modules, Component Lead Time Solutions.

Actual product photos available on request