MAX837EUS+T
Product Specifications
MAX837EUS+T
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The MAX837EUS+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
MAX837EUS+T: A 1.204 V Monitor Whose 6 mV Hysteresis Does Not Cover One Percent Resistors
The MAX837EUS+T is the push-pull member of the MAX836/MAX837 four-pin micropower voltage monitor pair from Analog Devices, in the 4-pin SOT143 package on tape and reel. It contains a 1.204 V band gap reference and a comparator, with the trip point set by two external resistors, so the same part monitors 2.5 V, 12 V or 24 V rails. The published table gives a 1.185 V to 1.215 V reference window at 25 C, 3.5 uA typical and 6.5 uA maximum supply current, a 2.5 V to 11 V supply range, 80 us of propagation delay, 35 us of glitch immunity, 6 mV of trip threshold hysteresis, and 3 nA typical and 12 nA maximum input leakage.
The divider is the accuracy, and the part is only a quarter of the error
The reference is plus or minus 1.25 percent at 25 C and plus or minus 2.6 percent over temperature, which reads as a precision part until the divider is added. For a 12 V rail the divider ratio is 9.97, so the threshold is 1.204 V times that ratio, and a pair of one percent resistors contributes two percent of 12 V, which is 240 mV. The reference contributes 1.25 percent of 12 V, which is 150 mV. The two together are 390 mV of threshold uncertainty on a 12 V rail, or 3.25 percent, and the 6 mV hysteresis referred to the 12 V rail is 60 mV, a quarter of the resistor error alone.
That ratio is why slow ramps chatter. A supply that rises through the trip point over 240 mV of resistor spread will cross and re-cross the 60 mV hysteresis band as the load changes, and the output follows each crossing. The fix is not a different monitor, it is a divider with 0.1 percent resistors or a deliberate external hysteresis resistor that widens the band to match the divider error.
Input leakage and a one megohm divider
The IN pin draws 3 nA typical and 12 nA maximum. Through a divider whose total resistance is 1 Mohm that leakage produces 12 mV at the IN pin, which the divider ratio turns into 120 mV at the monitored 12 V rail. A 1 Mohm divider also runs at 12 uA from a 12 V rail, continuous, which is more than twice the 6.5 uA the monitor itself draws. Lower the divider to 100 kohm and the leakage term falls to 12 mV at the rail while the divider current rises to 120 uA. The divider resistance is a trade between standing current and leakage error, and the monitor is not the dominant load in either case.
Where the 2.5 V to 11 V supply range bites
The IN pin is limited to VCC minus 1 V, so the divider output must stay at least 1 V below the monitor supply. Since the divider output sits at 1.204 V by definition, the monitor supply has to be at least 2.2 V, which is inside the published 2.5 V minimum. That also means the monitored rail can be far above the supply: a 24 V rail monitored from a 5 V supply is normal, because the divider drops the 24 V to 1.2 V before it reaches the pin. What the 11 V ceiling limits is the monitor supply, not the rail being watched.
| Parameter | Published value | What it decides |
|---|---|---|
| Reference | 1.204 V, 1.185 V to 1.215 V at 25 C | Plus or minus 1.25 percent before the divider |
| Reference over temperature | 1.169 V to 1.231 V | Plus or minus 2.6 percent |
| Hysteresis | 6 mV typical | 60 mV at a 12 V rail, a quarter of a 1 percent divider error |
| Divider for 12 V | Ratio 9.97, R1 over R2 of 8.97 | 240 mV of spread from one percent resistors |
| Input leakage | 3 nA typical, 12 nA maximum | 120 mV at the rail through a 1 Mohm divider |
| Supply current | 3.5 uA typical, 6.5 uA maximum | Less than the divider it drives |
| Supply range | 2.5 V to 11 V | The monitor supply, not the monitored rail |
| Output | Push-pull, 260 ns rise, 680 ns fall | Drives a logic input without a pull-up |
Questions buyers ask before they order this part number
MAX836 or MAX837? The MAX836 has an open-drain output that can be pulled above the monitor supply, up to 11 V, which is what a 5 V logic input needs when the monitor runs from 2.5 V. The MAX837 has the push-pull output that drives a logic pin directly and costs 680 ns on the falling edge. The choice is the destination of the output, not the accuracy.
Can one part cover both a 12 V and a 24 V rail? Yes, with two dividers and one monitor per rail, because the trip point lives in the resistors. What cannot be shared is the divider: a 24 V rail needs 120 mV of leakage error accounted for at twice the ratio, so the resistor values change with the rail even when the monitor does not.
The part is carried under analog and mixed-signal IC category. Buyers comparing supervisory thresholds across packages use pin to pin cross reference, and equipment that has to hold a monitor threshold through a long service life is usually listed under medical device components.
Request Quote — In Stock, 100% New & Original, Full Warranty