MAX9915EXT+T
Product Specifications
MAX9915EXT+T
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The MAX9915EXT+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
MAX9915EXT+T: 1 MHz for 20 uA, and What Is Left at a Gain of 10
The MAX9915EXT+T is the single channel with shutdown from the MAX9914 to MAX9917 CMOS amplifier family at Analog Devices, in the 6-pin SC70 package on tape and reel. The published summary gives a 1 MHz gain bandwidth product, 20 uA of supply current, a 1.8 V to 5.5 V single supply, 1 pA of input bias current, 200 uV of input offset voltage, rail-to-rail input and output ranges, unity gain stability, a shutdown mode that drops the supply current to 1 nA and puts the output into a high impedance state, and an operating range of -40 C to +85 C.
Fifty kilohertz of bandwidth per microamp, and where it goes
One megahertz for 20 uA is 50 kHz per microamp, which is the ratio this family is bought for. In a closed loop the usable bandwidth is the gain bandwidth divided by the noise gain, so a gain of 10 leaves 100 kHz and a gain of 100 leaves 10 kHz. Those are the frequencies where the loop gain reaches unity and the phase margin reaches zero, so the bandwidth a signal can actually use is roughly half of it once a 45 to 60 degree margin is kept: about 50 kHz at a gain of 10 and 5 kHz at a gain of 100. A 10 kHz filter stage is a comfortable fit, a 100 kHz one is not.
1 pA of bias current is smaller than the board
Bias current becomes an error only through the source resistance. At 1 pA, a 1 Mohm source produces 1 uV, a 10 Mohm source 10 uV and a 100 Mohm source 100 uV, so the 200 uV offset dominates until the source impedance passes 200 Mohm. Above that the bias term is the larger of the two, and the figure is a room temperature typical: leakage on a humid board, flux residue and a socket can each exceed 1 pA, which is why the input node of a circuit using this part is a cleaning and guard ring decision as much as a component decision.
The shutdown pin and what 20 uA costs over a year
20 uA at 3 V is 60 uW, and on a 220 mAh coin cell that is 11,000 hours, or 1.25 years, with nothing else drawing current. At 5 V the same current is 100 uW. Shutdown takes the part to 1 nA, which is twenty thousand times lower and 5.5 nW at 5.5 V, and it puts the output into a high impedance state so a multiplexer or a second amplifier behind it is not loaded by a disabled stage. That combination is what makes the part usable in a sensor node that wakes for a millisecond at a time.
The rail-to-rail input claim is worth reading with the electrical table open. Rail-to-rail input on a CMOS stage usually means the input common mode reaches both rails, and the crossover between the input pairs is where the offset step appears. For a buffer that has to work at the positive rail, the offset step at crossover is larger than the 200 uV headline, and it shows up as a distortion term rather than as a DC error.
| Parameter | Published value | What it decides |
|---|---|---|
| Gain bandwidth | 1 MHz | 50 kHz usable at a gain of 10 |
| Supply current | 20 uA | 60 uW at 3 V, 11,000 hours on 220 mAh |
| Bias current | 1 pA | 100 uV at a 100 Mohm source |
| Offset | 200 uV | Dominant until the source passes 200 Mohm |
| Supply range | 1.8 V to 5.5 V | Single cell to 5 V, no second rail |
| Shutdown | 1 nA, output high impedance | 20,000 times below the operating current |
| Temperature | -40 C to +85 C | Portable and consumer, not automotive |
| Package | 6-pin SC70 for the single with shutdown | 2 mm class footprint |
Questions buyers ask before they order this part number
Do I need the shutdown version? The MAX9914 is the same amplifier in a 5-pin SC70 without the shutdown pin, so the 6-pin part is only worth its extra lead if the circuit actually parks the amplifier. A board that leaves the enable tied high pays for a pin it never uses, and the 5-pin part is the smaller footprint.
Is 200 uV of offset enough for a DC measurement? For a 12 bit converter on a 3.3 V range the resolution is 806 uV, so 200 uV is a quarter of a bit and invisible. For a 16 bit converter on the same range the resolution is 50 uV, and the offset is four bits: that case needs a chopper stabilized amplifier or a calibration step, not a lower current part.
The family is listed in analog and mixed-signal IC category. Portable front ends are compared on amplifier cross reference, and sensor nodes whose bill of materials is being rebuilt around a shortage start from BOM shortage recovery.
Request Quote — In Stock, 100% New & Original, Full Warranty